![]() |
![]() |
#1 |
Master EcoRenovator
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
|
![]() Looking for pictures of Best Practices Plumbing of Heat Pump Internals.
|
![]() |
![]() |
![]() |
#2 |
Master EcoRenovator
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
|
![]() Is it OK to position flat plate HX condenser flat horizontal?
|
![]() |
![]() |
![]() |
#3 |
Supreme EcoRenovator
|
![]() Not unless you want your hx to be full of oil.
Last edited by jeff5may; 05-24-14 at 01:23 PM.. |
![]() |
![]() |
The Following User Says Thank You to jeff5may For This Useful Post: | buffalobillpatrick ![]() |
![]() |
#4 |
Supreme EcoRenovator
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
|
![]() Plate exchangers should be mounted so the liquid side faces down and water (or other secondary fluid) flow is opposite refrigerant flow. The small connection is for the liquid line.
On the evaporator, the small connection is the liquid inlet. As such, the water flow should actually be opposite to what is drawn. (The drawn flows are for using it as a condenser.) Mount all the refrigerant parts to the base plate (recommended to have it on wheels for easy movement) before you braze it together. That avoids unnecessary stress on the joints.
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her... |
![]() |
![]() |
The Following User Says Thank You to NiHaoMike For This Useful Post: | buffalobillpatrick ![]() |
![]() |
#5 |
Master EcoRenovator
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
|
![]() Does the little Desuperheater HX need to be above the condenser & drain into top of condenser? (enclosure would be quite tall)
OR Can Desuperheater be next to condenser & have it's output (bottom) pipe routed upward to input (top) of condenser? |
![]() |
![]() |
![]() |
#6 |
Supreme EcoRenovator
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
|
![]() The desuperheater can be mounted in any position, but it doesn't hurt to keep the outlet near the bottom.
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her... |
![]() |
![]() |
The Following User Says Thank You to NiHaoMike For This Useful Post: | buffalobillpatrick ![]() |
![]() |
#7 |
Master EcoRenovator
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
|
![]() I copied this from a place selling desuperheaters, is this true, or just sales hype?
"Due to increased condensing area now available to the refrigerant gas, the discharge pressure after the compressor gets reduced. This would result in about 5% savings of Power consumed by the compressor motors. Additionally, the liquid coming out of condenser gets sub- cooled. Every 2° C drop in the liquid temperature increases the system COP by 5 % i. e. , it reduces the power consumption relatively." |
![]() |
![]() |
![]() |
#8 |
Supreme EcoRenovator
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
|
![]() It's equivalent to oversizing the condenser. When the condenser is already oversized, the power use and optimum subcooling won't change much, but the desuperheater will give you a small amount of hotter water along with a large amount of hot water, meaning better overall efficiency.
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her... |
![]() |
![]() |
The Following User Says Thank You to NiHaoMike For This Useful Post: | buffalobillpatrick ![]() |
![]() |
|
|