![]() |
![]() |
#121 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
![]() Yeah, multiply your R22 load by 0.4 and it's your R290 load.
It sure seems like the R290 is a drop-in replacement for R22, pressure wise too.. ![]()
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. |
![]() |
![]() |
![]() |
#122 |
Helper EcoRenovator
Join Date: Aug 2010
Posts: 44
Thanks: 10
Thanked 4 Times in 2 Posts
|
![]() Ha ha, just went to visit these guys,( refrigerantguys.com) they are a US distributor of a Italian company, will be importing new European refrigerants, talked about r 600, maybe r744 too?
|
![]() |
![]() |
![]() |
#123 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
![]() I got my R410A from those guys. The sell on Ebay and their prices don't seem to be unreasonable,
compared to a few others I checked out.. I like the company, their support is pretty good. R600 sounds interesting. It should cost a little less than R410A.. But, how will the price compare to DIY filtered & dried BBQ gas?? ![]() R744 (CO2) will be illegal in the USA soon. Unless the current regime is kicked out. ![]() I can't see using CO2, it's pressures are a lot higher than R410A, which is a high pressure gas. ![]() This a tank chart. On the bottom, it's how full the tank is.. If a tank of C02 is 60% full, and the temp is 120 deg F, the tank's pressure shoots up to 1400 PSI.. ![]() At room temp (70F), it's okay.. Around 850 psi.. Good for paintball shooting..
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. |
![]() |
![]() |
![]() |
#124 |
Helper EcoRenovator
Join Date: Jun 2011
Location: Norway
Posts: 63
Thanks: 3
Thanked 10 Times in 10 Posts
|
![]() CO2 can be used, but only in high thermal difference sites, the return temperature on the high side must be quite low. It will be working without phase shift, but can then give COP of 10 or above in good conditions. They run in supercritical mode using the Lorentz Cycle, described here:
Supercritical carbon dioxide - Wikipedia, the free encyclopedia Heat pump - Wikipedia, the free encyclopedia The pressure is insane though. If you worry about Propane, this is not for you :-p |
![]() |
![]() |
![]() |
#125 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
![]() CO2 pressures are not so insane, my air rifles use 200 and 300 bar.
I don't understand phase change all that well, (I just know it works) to understand how CO2 could work in a heat pump system, without changing from liquid to gas.. And back. I've seen what happens when CO2 gets too warm or too confined. And it seems like Propane would be safer, pressure wise. I'll have to do some reading.. Propane is an alternative refrigerant with both a good and bad side. ![]() It's the one I would use if I had no other good choice. Edit: http://www.annex32.net/pdf/presentat...yoto_Stene.pdf I was just skimming this Annex 32 paper and saw this explanation.. "3. ANALYSIS OF INTEGRATED CO2 HEAT PUMPS FOR RESIDENCES Carbon dioxide (CO2, R744) has an especially low critical temperature (31.1ºC) and high critical pressure (73.8 bar). As a consequence, the operating pressure in CO2 heat pump systems will typically be 5 to 10 times higher than that of HFC systems, i.e. 20 to 40 bar in the evaporator and 80 to 130 bar during heat rejection. Due to the low critical temperature most CO2 heat pumps operate in a so-called transcritical cycle with evaporation at subcritical pressure and heat rejection at supercritical pressure (p>73.8 bar). Unlike a subcritical heat pump cycle, heat is not given off by means of condensation of the working fluid in a condenser but by cooling of high-pressure CO2 gas in a heat exchanger (gas cooler). The temperature drop for the CO2 gas during heat rejection is denoted the temperature glide. Figure 3.1 shows the principle of the transcritical CO2 heat pump cycle in a Temperature-Enthalpy diagram. " It seems (to me) that a CO2 ASHP hotwater heater's layout and function would be somewhat similar to a mini-split in heating mode. Where the IDU's coil (inside a water tank) would be the highest pressure (highest temperature) in the loop. The pressure would drop inside the outdoor HX, where it would pick up heat from the air flow..
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. Last edited by Xringer; 12-29-11 at 09:19 AM.. Reason: adding link etc |
![]() |
![]() |
![]() |
#126 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
If you think this is true, prove it. -AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
![]() |
#127 | |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
![]() Quote:
![]() Like this: http://lh4.ggpht.com/_sd4aOA0Ur-I/Sx...umb%5B1%5D.jpg And this: http://lh6.ggpht.com/_sd4aOA0Ur-I/Sx...ity%5B5%5D.jpg
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. Last edited by Xringer; 12-29-11 at 08:40 AM.. Reason: saving space |
|
![]() |
![]() |
![]() |
#128 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
-AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
![]() |
#129 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
![]() Maybe I'm trying to start a CO2 Truther Faction..?.
If Sanyo has been making CO2 compressors for over 10 years (and inverter models since 2005), What is a CO2 compressor? | CO2 Compressors | Compressors HOME | SANYO Why isn't my Mini-Split running on CO2?? ![]() ![]()
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. |
![]() |
![]() |
![]() |
#130 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Even this statement is disinformation.
You are flattering yourself if you imagine that you are a 'truther'. There is nothing truthful about: Quote:
To abuse a forum where people come to get actual, true and useful information about reducing their energy consumption, for your purposes of passing on undigested disinformation, or worse yet, generating your own disinformation, is an insult. * * * At one point, the Webmaster of EcoRenovator wanted to move all of the posts that pertained to R-290 from the 'Manifesto' thread and put them all into this thread, that you started. I countered that idea, because even in the beginning, I could see that there would be very little useful, practical information regarding the use of R-290 here, and I didn't want useful information to get drowned out in useless information. Thirteen pages later, I'm glad I made the correct call. -AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
![]() |
|
|