EcoRenovator  

Go Back   EcoRenovator > Improvements > Geothermal & Heat Pumps
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts


Reply
 
Thread Tools Display Modes
Old 12-07-21, 11:56 PM   #1
Bobinater33
Lurking Renovator
 
Join Date: Dec 2021
Location: Buckeye,Az
Posts: 18
Thanks: 2
Thanked 8 Times in 6 Posts
Default GMCC Inverter Rotary Compressors

Greetings,

Long time lurker and decided to register finally. Awesome forum. Finally a place for like minded individuals. The folks on HVAC talk and the various HVAC Facebook groups are a bunch of trade preservationist who will deliberately block outsiders from conducting any sort of experimentation. God forbid you find out how much a run cap replacement should really cost. Anyways..


So before I go applying power to my current WSHP water heater build, I’d like to know what to expect if I apply 220v single phase power to a mr. cool 18k btu compressor. Something tells me I won’t get what I’m looking for when the inkbird tells the contactor it needs heat and it closes those contacts. �� . Having 2 lbs of r290 sitting it might even make things interesting if it’s single phases and becomes rapidly hot.

It’s tough getting any information on them as they only furnish this documentation to their registered “partners” aka manufacturers…It’s a GMCC rotary compressor and the only information it gives is a model number and “160v at 180hz” and “Rated for flammable refrigerant”. My guess is that it’s the company’s cryptic way of indicating the ratio to which the inverter bored should drive the comp.


I have a smaller single phase comp which for sure runs on 110v but it’s capacity is an issue…. I have several of these GMCC rotary comps that I’d really like to put to use.

Bobinater33 is offline   Reply With Quote
Old 12-16-21, 06:51 AM   #2
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,431
Thanks: 431
Thanked 619 Times in 517 Posts
Send a message via Yahoo to jeff5may
Default

Welcome to the forums! Been busy with life this holiday season. I saw your other post, sounds like it will run off a VFD just fine.

For more information, post up the donor unit model number and the compressor model number. Having those two usually is enough to figure out exactly what you have to work with.
jeff5may is offline   Reply With Quote
Old 12-17-21, 12:50 AM   #3
Bobinater33
Lurking Renovator
 
Join Date: Dec 2021
Location: Buckeye,Az
Posts: 18
Thanks: 2
Thanked 8 Times in 6 Posts
Default

Well appearently I did something wrong and fried the unit, all it would do is make a high frequency noise. It kept tripping on inverter over current before it finally went bang. I looked closer and the IPM chip itself exploded. Nice little 250 dollar mistake.

This is a brand new compressor too. It’s a 24k btu twin rotary 380v BLDC from what little info I could find on it. Model number: da250s2c-30mt. It came packaged under vacuum with the rubber plugs in the ports.
Bobinater33 is offline   Reply With Quote
The Following User Says Thank You to Bobinater33 For This Useful Post:
Lawrence (02-11-22)
Old 02-11-22, 10:23 AM   #4
Lawrence
Lurking Renovator
 
Join Date: Feb 2022
Location: Alpine
Posts: 1
Thanks: 22
Thanked 0 Times in 0 Posts
Default

Bob, I have picked up a similar unit with a GMCC compressor. It's marked 180V at 180Hz. Also looking to run it on VFD if possible. Which VFD did you try and why do you think it ended badly?

Also- I found this website that breaks down the GMCC compressor model numbers - it show the power usage and a COP.

www \dot\ hvacrcompressor.com/gmcc-rotary-compressor

I've been reading every thread I can on here about heat pumps. It seems that these inverter units are a tough nut to crack for the home hacker.
Lawrence is offline   Reply With Quote
Old 02-11-22, 09:14 PM   #5
NiHaoMike
Supreme EcoRenovator
 
NiHaoMike's Avatar
 
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
Default

Perhaps look at the Openinverter project? They specialize in reverse engineering BLDC motors out of EVs, it should be pretty easy to adapt to BLDC compressor motors.
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her...
NiHaoMike is offline   Reply With Quote
Old 02-11-22, 10:30 PM   #6
Bobinater33
Lurking Renovator
 
Join Date: Dec 2021
Location: Buckeye,Az
Posts: 18
Thanks: 2
Thanked 8 Times in 6 Posts
Default

Quote:
Originally Posted by NiHaoMike View Post
Perhaps look at the Openinverter project? They specialize in reverse engineering BLDC motors out of EVs, it should be pretty easy to adapt to BLDC compressor motors.
I’m going to loook into that. Very interesting .


I went ahead and just bought me a 208/230v 60hz 1 phase LG Scroll for 240 bucks on surplus city liquidators

Bobinater33 is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:46 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design