EcoRenovator  

Go Back   EcoRenovator > Improvements > Solar Power
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 03-24-13, 04:43 PM   #1
michael
Michael
 
Join Date: Feb 2013
Location: mendocino, california
Posts: 67
Thanks: 7
Thanked 2 Times in 2 Posts
Default DIM 5500 w PV Array

The following photos chronicle in a spotty fashion a single axis tracking solar array I finished recently. It took two years to design and build. It serves two residences and generates slightly more electricity than the two homes use. It is grid tied, so we use PG&E as our battery pack. The panels are 230 w Sunpower, and were installed on the array by a local company, Mendocino Solar. I built all of it myself, but I had lots of help. I used Parallax microcontrollers, and received help and guidance from the Parallax Users' Forum, from a local generous neighbor, Jonathan Peakall, and from my son, Patrick Moreland. Those are the folks who were given the daunting task of teaching me how to write code for the microcontroller. The motor, which has an additional microcontroller in it, was provided by the robotics company for which my son works. A very short video of the array working can be viewed by going on Youtube.com and searching "trackingQT1."

There was a good deal of welding involved, and the photo of the rocker arms shows a bit of the welding set up. I used a TIG welder for all the mild steel, which I later had galvanized, the stainless and the aluminum.

Each morning the controller wakes a bit before sunrise, elevates the array until it hits a limit switch which sets the beginning point for the day. It takes a few minutes to establish contact with a GPS satellite to determine the day and exact time, checks look-up tables that were derived from sun charts to find the correct orientation to begin the day, and sets the array to that angle. It corrects the position hourly until just after sunset when the array is returned to its steepest angle (to help prevent dust build up), and goes to sleep.

I'll be happy to answer questions, and I'll be happy to share any part of the programming code.


Last edited by michael; 03-27-13 at 08:36 PM..
michael is offline   Reply With Quote
Old 03-24-13, 04:45 PM   #2
michael
Michael
 
Join Date: Feb 2013
Location: mendocino, california
Posts: 67
Thanks: 7
Thanked 2 Times in 2 Posts
Default

First photos: These include the beginning stages of preparing for the frame, the concrete base, and finally a shot of the home-made rocker arms before they were galvanized.
Attached Thumbnails
Click image for larger version

Name:	1.jpg
Views:	523
Size:	584.8 KB
ID:	3082   Click image for larger version

Name:	2.jpg
Views:	508
Size:	550.1 KB
ID:	3083   Click image for larger version

Name:	3.jpg
Views:	505
Size:	291.2 KB
ID:	3084   Click image for larger version

Name:	4.jpg
Views:	502
Size:	277.0 KB
ID:	3085   Click image for larger version

Name:	5.jpg
Views:	492
Size:	246.5 KB
ID:	3086  

Click image for larger version

Name:	6.jpg
Views:	512
Size:	183.6 KB
ID:	3087  

Last edited by michael; 03-24-13 at 04:49 PM..
michael is offline   Reply With Quote
Old 03-24-13, 04:56 PM   #3
michael
Michael
 
Join Date: Feb 2013
Location: mendocino, california
Posts: 67
Thanks: 7
Thanked 2 Times in 2 Posts
Default

Photo group 2: Prototype of array mover where I learned how to connect with GPS and how to control the motor. Views of the control box showing the microcontroller and GPS modules. View of the limit switches to set the day's motion as well as to disable the power in case of an error.
Attached Thumbnails
Click image for larger version

Name:	7.jpg
Views:	494
Size:	54.3 KB
ID:	3088   Click image for larger version

Name:	9.jpg
Views:	495
Size:	197.1 KB
ID:	3089   Click image for larger version

Name:	10.jpg
Views:	485
Size:	159.0 KB
ID:	3090   Click image for larger version

Name:	11.jpg
Views:	488
Size:	176.4 KB
ID:	3091   Click image for larger version

Name:	12.jpg
Views:	476
Size:	143.2 KB
ID:	3092  

Click image for larger version

Name:	13.jpg
Views:	467
Size:	74.4 KB
ID:	3093  
michael is offline   Reply With Quote
Old 03-24-13, 04:57 PM   #4
michael
Michael
 
Join Date: Feb 2013
Location: mendocino, california
Posts: 67
Thanks: 7
Thanked 2 Times in 2 Posts
Default

Final photo group showing the back and front views of the finished array
Attached Thumbnails
Click image for larger version

Name:	8.jpg
Views:	528
Size:	209.9 KB
ID:	3094   Click image for larger version

Name:	14.jpg
Views:	569
Size:	285.4 KB
ID:	3095  
michael is offline   Reply With Quote
Old 06-25-13, 10:27 AM   #5
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,913
Thanks: 170
Thanked 558 Times in 458 Posts
Default

Quote:
Originally Posted by michael View Post
Final photo group showing the back and front views of the finished array
This is a sweet... install it looks great.
pinballlooking is offline   Reply With Quote
The Following User Says Thank You to pinballlooking For This Useful Post:
michael (06-26-13)
Old 03-24-13, 10:16 PM   #6
greif
a van down by the river
 
Join Date: Jun 2011
Location: Kaukauna,WI
Posts: 108
Thanks: 6
Thanked 5 Times in 5 Posts
Default

Good job michael
__________________
Gary R

“If you want total security, go to prison. There you're fed, clothed, given medical care and so on. The only thing lacking... is freedom. ” ― Dwight D. Eisenhower
greif is offline   Reply With Quote
Old 03-25-13, 02:17 PM   #7
Exeric
Apprentice EcoRenovator
 
Join Date: Aug 2012
Location: California
Posts: 274
Thanks: 19
Thanked 37 Times in 28 Posts
Default

It sounds and looks very sophisticated. Quite an accomplishment.
Exeric is offline   Reply With Quote
The Following User Says Thank You to Exeric For This Useful Post:
michael (03-25-13)
Old 03-25-13, 03:33 PM   #8
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,518
Thanks: 1,156
Thanked 374 Times in 305 Posts
Default

Very impressive setup.

What made you go with vertical tracking, but not horizontal tracking?

Also, would you care to share how much $ you have into that setup?
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 03-25-13, 05:05 PM   #9
michael
Michael
 
Join Date: Feb 2013
Location: mendocino, california
Posts: 67
Thanks: 7
Thanked 2 Times in 2 Posts
Default

Hello Daox, If you mean why single axis vs two axis tracking, it was far too complicated for me to design a two axis tracker, and it wd have taken several to mount 24 panels. Also, our local codes allow a nearly permit free array as long as it isn't taller or higher than 6'. If you mean why an east west axis vs north south axis, I had a couple of reasons. First, the site lent itself to an east west axis; that's where the room was. Second, we're in a bowl created by surrounding trees that blocks the sun until it is 15-20 degrees above the horizon. N-S axes turn the panels directly toward the sunrise and sunset, those are the best angles, and those were the times when we had least access to the sun.

We have quite a bit of money in the set up, as you might guess. The panels cost about $900 each. I think I built the array for about $3000, and most of that went into the aluminum I beam and channel. None of the metals were cheap! And that doesn't count the cost of the TIG welder that I bought used for about $1500. We got a rebate from the electric company for about $5000 and a tax credit of about $11000, both of which mean that folks like you helped me build this thing, I'm ashamed to say. The solar industry has got to get off welfare, but for that matter, the same is way overdue for the oil industry. In the end, we were out of pocket about $28k for the thing, all the little details included. It's rated to last a minimum of 30 years, but unless electricity goes up a bunch, it will never pay for itself because our electric bill was only about $1200/year before the array; now it's zero. It just seemed like the right thing to do with the cash we had at the time, and it was the most fun, challenging thing of that sort that I've ever done. I guess the failure to break even aspect of it was just the price of admission. mm
michael is offline   Reply With Quote
The Following User Says Thank You to michael For This Useful Post:
Daox (03-25-13)
Old 03-25-13, 09:09 PM   #10
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,518
Thanks: 1,156
Thanked 374 Times in 305 Posts
Default

If you over produce, do you get paid by your utility?
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Reply


Tags
array, photovoltaic, solar, tracking

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:22 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design