EcoRenovator  

Go Back   EcoRenovator > Improvements > Solar Heating
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 11-03-20, 02:24 PM   #11
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,452
Thanks: 1,101
Thanked 362 Times in 294 Posts
Default

More progress today. I found a panel that had two leak points in it. I haven't done much sweating of pipe, but I managed to get them sealed up.

How it was.





Cleaned up and ready for flux.





Yay, no more leaks.




I also had this one to fix up. Cleaning it out was a pain. I used a file and sand paper to clean the area. It took a while and two attempts, but its sealed now.


Attached Thumbnails
Click image for larger version

Name:	IMG_20201103_105805949.jpg
Views:	76
Size:	225.4 KB
ID:	9116   Click image for larger version

Name:	IMG_20201103_111250898.jpg
Views:	74
Size:	170.5 KB
ID:	9117   Click image for larger version

Name:	IMG_20201103_111514303.jpg
Views:	73
Size:	183.4 KB
ID:	9118   Click image for larger version

Name:	IMG_20201103_113855992.jpg
Views:	77
Size:	195.8 KB
ID:	9119  
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 11-05-20, 07:34 PM   #12
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,452
Thanks: 1,101
Thanked 362 Times in 294 Posts
Default

Today was the last day of pressure testing. Everything has now passed. Hurray!

The next step is to start assembling. Today I got the inserts all put in the cases, and all the inserts got a new thin coat of flat black paint (in the picture is still drying).

Attached Thumbnails
Click image for larger version

Name:	IMG_20201105_154449755_HDR.jpg
Views:	66
Size:	192.7 KB
ID:	9120  
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 11-06-20, 02:06 PM   #13
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,452
Thanks: 1,101
Thanked 362 Times in 294 Posts
Default

I have a question about the reassembly of these panels. The glass on them has a rough texture on one side of it. I assume this is to refract light and even out the distribution over the panel. My question is, should it be on the outside or inside?
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 11-12-20, 12:04 AM   #14
Acuario
Apprentice EcoRenovator
 
Join Date: May 2011
Location: Tortosa, Spain
Posts: 204
Thanks: 2
Thanked 61 Times in 38 Posts
Default

Quote:
Originally Posted by Daox View Post
This part is all easy. The hardest part is actually removing the PEX lines. Once they're crimped on there they are very hard to pull off, even after cutting the metal crimps off. If anyone has any tips on how to remove PEX lines from then fittings it sure would be nice.
A very sharp knife and a lot of care! When I have to remove PEX fittings I cut a deep slit into the pipe the length of the fitting following the line of the pipe, but not down to the fitting. At the end of the fitting I cut right into the pipe for about 1cm. Then bending the pipe at the fitting the slit should open up and you can recover your fitting. Be careful not to cut into the fitting as if the ridges are damaged it can leak - particularly the plastic fittings.

Personally I wouldn't use PEX tube for a solar installation. In the past I used a plastic pipe (not PEX) and with the combination of heat and pressure it ended up popping.

Also, if you do use PEX be aware that some (maybe all, I don't know) is very susceptible to UV and degrades and ends up leaking. In Spain the most common is a translucent white PEX and I have seen lots of instances where it has been installed outside by inexperienced people and then has started to leak - I've changed lots to copper. It seems to last about 5 years before failing. It ends up very fragile and almost crystalized, if you try to expand it it just splits so repair is impossible.

Acuario is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:08 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design