EcoRenovator  

Go Back   EcoRenovator > Improvements > Energy Storage
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 03-22-14, 08:59 PM   #11
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

From this study:
http://www.worldenergy.org/documents...papers/412.pdf

Paraffin:
coefficient of thermal conduction – solid = .2W/mK
coefficient of thermal conduction – liquid = .15W/mK

Paraffin is a pretty good insulator (both thermal & electrical)

They put the paraffin into vertical SS 2.35" (60mm) tubes to increase surface area.
But they were looking for quick freeze/thaw times.

It seems that a 275gal IBC Tote tank won't have enough surface area? for a daily freeze/ thaw, but do I need that?

If I get enough winter solar gain that on average all the paraffin gets melted, then I think I can make it through 3-4 days of bad solar conditions with useful heat in tank. ?????

BBP


Last edited by buffalobillpatrick; 03-22-14 at 09:05 PM..
buffalobillpatrick is offline   Reply With Quote
The Following User Says Thank You to buffalobillpatrick For This Useful Post:
Lawrence (02-22-22)
Old 02-28-16, 06:09 AM   #12
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
Default

BBP,

Any updates on how this all worked out?

Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Old 02-28-16, 09:37 AM   #13
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

Hi Steve, on hold until I sell current house.
buffalobillpatrick is offline   Reply With Quote
Old 03-03-16, 01:02 PM   #14
Mobile Master Tech
Apprentice EcoRenovator
 
Mobile Master Tech's Avatar
 
Join Date: May 2012
Location: Atlanta, Ga
Posts: 142
Thanks: 38
Thanked 41 Times in 34 Posts
Default

BBP, thanks for linking to this thread. Nice tank!

First, PEX has low thermal conductivity, especially in 3/4" or larger because of the wall thickness. For not much more, you can get 1' corrugated stainless that has twice the surface area, tons more turbulence and probably quadruple the heat transfer. I got lucky and got a 98ft roll for under $100 shipped on ebay.

If you will be cycling the tank across the PCM's melt temp frequently, PCM makes sense. If only a few times per year, I would just use water and call it a day. Paraffins will be stable at any temp, salt hydrates are sensitive to temperature extremes. Candle wax for pillar and taper candles melts at a higher temp than wax for votives, container candles, etc. The potentially cheap price may offset the range of melt temp and slightly lower enthalpy.

Stratification only happens in the lower reaches of a 5ft or deeper still tank, not much happens in the top few feet or if there is any turbulence whatsoever. If you positioned your HX coils below the level of the wax so the wax doesn't insulate it but still within the top few feet, it will be as effective as if it were at the top. You could also float heatset PET, or even PP bottles full of wax to prevent the insulating effect. Tidier than "free-range" wax. Tie a cord to them if using a PCM heavier than water.

Put heavygage aluminum foil down the center of the bottles and use bottles with 8" or smaller cross section if you use paraffins and you want to get the heat out before the next ice age.
__________________
"I‘d put my money on the sun and solar energy. What a source of power! I hope we don‘t have to
wait until oil and coal run out before we tackle that." Thomas Edison, 1847 — 1931

Last edited by Mobile Master Tech; 03-15-16 at 07:09 AM..
Mobile Master Tech is offline   Reply With Quote
The Following User Says Thank You to Mobile Master Tech For This Useful Post:
Lawrence (02-22-22)
Old 03-03-16, 01:28 PM   #15
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

[/IMG]

DIY Hydraulic Seperator / Mixer

Taco 007 on left side input, speed controlled by Erie BB3000 with it's temperature controlling sensor on output right side after Grundfos Alpha

buffalobillpatrick is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:57 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design