EcoRenovator  

Go Back   EcoRenovator > Improvements > Appliances & Gadgets
Advanced Search
 


Blog Register 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 02-04-14, 12:37 PM   #1
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default Build your own EV charger. open-evse Open Electric Vehicle Supply Equipment (EVSE)

Ok let me start by saying it really is not a charger. All the EV vehicles have the chargers built in you just need to supply power and communication and safety to get it to charge your EV.

There are commercial units available they are expensive and not very flexible. Open EVSE will let you charge with 120 or 240 volts. This will do 3.3KW- 10KW charging. And beyond.

OpenEVSE_Compatibility - open-evse - OpenEVSE is known to be compatible with OpenEVSE Plus: - Open Electric Vehicle Supply Equipment (EVSE) - Google Project Hosting


OpenEVSE - a DIY charge station

I bought OpenEVSE Plus v2
OpenEVSE_boards - open-evse - Comparison OpenEVSE boards. - Open Electric Vehicle Supply Equipment (EVSE) - Google Project Hosting

EV Simulator
EVSimulator - open-evse - Assembly and Operation. - Open Electric Vehicle Supply Equipment (EVSE) - Google Project Hosting

RGB LCD Shield Kit w/ 16x2 Character Display
RGB LCD Shield Kit w/ 16x2 Character Display - Only 2 pins used! [NEGATIVE DISPLAY] ID: 714 - $24.95 : Adafruit Industries, Unique & fun DIY electronics and kits

(he now offers a display that is simpler to build and setup) he now offers a combo kit that will save having you from hunting down the other parts. I bought the kit before he offered this service.
Chris’s store OpenEV Store - OpenEV Store

I now have everything soldered on the boards. I have a few more parts on the way before I can finish this project.













Attached Thumbnails
Click image for larger version

Name:	OpenEVSEPlusV2.jpg
Views:	4578
Size:	38.5 KB
ID:	3952   Click image for larger version

Name:	EV_SimulatorKit.jpg
Views:	5180
Size:	279.7 KB
ID:	3953   Click image for larger version

Name:	OpenEVSE_SingleDPST_relay.jpg
Views:	6935
Size:	155.6 KB
ID:	3954   Click image for larger version

Name:	parts.jpg
Views:	4934
Size:	77.1 KB
ID:	3955   Click image for larger version

Name:	AddDisplay.jpg
Views:	5012
Size:	61.9 KB
ID:	3956  

Click image for larger version

Name:	41bQA7ubc3L._SX800_.jpg
Views:	4988
Size:	23.2 KB
ID:	3968  

Last edited by Daox; 02-04-14 at 02:27 PM..
pinballlooking is offline   Reply With Quote
The Following 4 Users Say Thank You to pinballlooking For This Useful Post:
Daox (11-18-19), NeilBlanchard (02-19-14), philb (12-20-14), Ryland (02-04-14)
Old 02-04-14, 12:55 PM   #2
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

Here are my boards so far after I soldered them.



Attached Thumbnails
Click image for larger version

Name:	20140204_134738.jpg
Views:	5545
Size:	62.4 KB
ID:	3960   Click image for larger version

Name:	20140204_134708.jpg
Views:	4733
Size:	59.1 KB
ID:	3961  

Last edited by Daox; 02-04-14 at 02:27 PM..
pinballlooking is offline   Reply With Quote
Old 02-16-14, 06:55 PM   #3
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

I got my programmer in the mail it was delayed by the snow. I loaded the latest code and I wired the display.

Time to build the rest.

Attached Thumbnails
Click image for larger version

Name:	20140216_194847.jpg
Views:	5350
Size:	57.8 KB
ID:	4024  

Last edited by Daox; 02-17-14 at 10:44 AM..
pinballlooking is offline   Reply With Quote
Old 02-23-14, 08:23 PM   #4
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

I finished the putting together the open source EVSE. It is now helping my Chevy Volt get charged up.
One good side benefit is it uses less than 1 watt in standby. This should help in my quest to lower my standby load.

It was a lot of drilling and getting everything to fit in the box. The 10 gauge wire is very stiff to work with. I am happy with the end results.
For the 8 gauge wire I used left over pieces from my solar project.

The second picture shows it actually charging my Volt.

I based my component layout off this build.
http://code.google.com/p/open-evse/wiki/30A_OpenEVSE


A lot of the parts I ordered were based off this build.
http://code.google.com/p/open-evse/wiki/EVSE_by_4Dolio



Attached Thumbnails
Click image for larger version

Name:	20140223_175412.jpg
Views:	5318
Size:	45.2 KB
ID:	4080   Click image for larger version

Name:	20140223_175424.jpg
Views:	4924
Size:	35.8 KB
ID:	4081  

Last edited by pinballlooking; 02-05-17 at 10:43 PM..
pinballlooking is offline   Reply With Quote
Old 02-24-14, 08:49 AM   #5
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

Things I would do different.

The fuse holder I bought is working fine but it could be beefier.
This is a better choice.

OpenEV Store - 30A Cooper Bussman Miget Fuse Holder
He did not sell these when I bought the kit. (Other people also sell this fuse holder)

He was out of the displays when I bought my kit. This one is simpler and more compact.

OpenEV Store - DIY - OpenEVSE RGB LCD

Metal enclosure would be stronger and just a little bigger would give more options for mounting things.

Indoor the plastic one is fine.

Things I liked or would do again.


The Leviton cable with J1772 plug is top quality. (Try to get this on sale)
I got this on a black Friday deal and it was a great deal. I got the 25’ version but they don’t sell this one any more. Buy the 30 amp cord even if you don't need it your next EV will need it and you will be all set.

https://store.leviton.com/collection...nt=18215948867

If you use the Leviton cable buy Strain Relief Cord Connectors - PG 21. It is a very tight fit but the next size up will not work at all. I had to send a set back and order these. you will need some soapy water and maybe light sand the cable to get them on. but they need to have a tight fit or they are useless.

I would buy the OpenEVSE Programmer again.
OpenEV Store - OpenEVSE Programmer
This allows up to load the latest software or bug fixes.

The EV simulator kit is a must have.
OpenEV Store - EV Simulator Kit
This allows you to test out the whole thing before plugging in that very expensive car. Then you know you did not mess it up.

Read all directions very carefully. Don’t drill into your work table

Look over other peoples builds to decide how you want yours.
http://code.google.com/p/open-evse/wiki/30A_OpenEVSE

Last edited by pinballlooking; 01-16-18 at 05:14 PM..
pinballlooking is offline   Reply With Quote
Old 12-20-14, 07:10 PM   #6
karl0525
Lurking Renovator
 
Join Date: Dec 2014
Location: north texas
Posts: 11
Thanks: 1
Thanked 0 Times in 0 Posts
Default Juice box(base addition)

Hello pinballlooking i bought a juice box level 2 charging kit from kickstarter a few months back and after looking at it i think i would need someone to build it for me. It includes all the parts except the charge cable. I to have a chevy volt and would like to be able to level 2 charge.If this is something we could discuss $ or maybe do a trade for 1 of your kits i am open to suggestions thanks.
karl0525 is offline   Reply With Quote
Old 08-16-16, 09:29 AM   #7
WyrTwister
Master EcoRenovator
 
Join Date: Jun 2013
Location: USA
Posts: 543
Thanks: 6
Thanked 44 Times in 38 Posts
Default

Just for information , what would the open Source EVSE do if you feed it 120 VAC in stead of 240 VAC ?

208 VAC ?

God bless
Wyr
WyrTwister is offline   Reply With Quote
Old 08-16-16, 09:50 AM   #8
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

It looks like it depends on what version you are using.

Can I use the 50A deluxe kit with 120V : OpenEVSE Support
Version 4 using 120v relay (not the normal method) : OpenEVSE Support

Mine is hard wired to 240 volt. I moved my old EVSE to my lake place. It used way to much standby power so I just flip off the breaker when we are not there.
__________________
Current project Aquaponics system , Passive Solar Greenhouse build

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Solar Install 12.5 Kwh-
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Mini Split installs -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

EV Chevy Volt -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
pinballlooking is offline   Reply With Quote
Old 11-18-19, 07:59 AM   #9
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,715
Thanks: 154
Thanked 512 Times in 419 Posts
Default

Time for an update.
Almost five years ago I built this EVSE. We used it to charge our car two times a day four years.

This last year we usually only charge once a day my son has his own car and drives himself to school every day.

During this time, I have had the one fuse blow twice. Since this was the second time the fuse blew. I took it off the wall to investigate why it was blowing the fuse.
It turns out the fuse holder that I did not really like had the female spade connector loosen up.
This was on the side the fuse was blowing. I crimped it down and resembled it. I built this in a water proof box.

I could see where some heat was building up so I drilled two 3/8 holes on the top and one on the bottom. This will let the heat out.
It is back to charging my car again.
__________________
Current project Aquaponics system , Passive Solar Greenhouse build

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Solar Install 12.5 Kwh-
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Mini Split installs -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

EV Chevy Volt -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
pinballlooking is offline   Reply With Quote
The Following User Says Thank You to pinballlooking For This Useful Post:
Daox (11-18-19)
Old 11-18-19, 08:41 AM   #10
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,426
Thanks: 1,076
Thanked 358 Times in 293 Posts
Default

Do you recall what was your total cost for this project was? Aren't there EVSEs out there for like $300? That Levition cable alone is nearly $200.

__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:15 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design