09-15-13, 11:33 PM | #91 |
Lurking Renovator
Join Date: Apr 2012
Location: Atlanta
Posts: 7
Thanks: 0
Thanked 1 Time in 1 Post
|
Clothes Dryer Heat Exchanger
Here is the latest of four video I have on youtube...I am pretty happy with the design: Clothes Dryer Heat Exchanger Part 4 - YouTube[/url]
Or search clothers dryer heat exchanger 6monty6 Let me know what you think! Thanks, Mark |
09-15-13, 11:37 PM | #92 |
Apprentice EcoRenovator
Join Date: Aug 2010
Location: Lakehills, Tx
Posts: 168
Thanks: 4
Thanked 10 Times in 9 Posts
|
There are No links!!!!!!!
Last edited by iamgeo; 09-15-13 at 11:48 PM.. |
09-16-13, 10:46 AM | #93 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
|
You can't post links, until after you've made some postings. I think it's 5 or 6..
__________________
My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less.. |
09-16-13, 04:28 PM | #95 |
Steve Hull
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
|
Gascort,
Great idea using counter current concept, but here is a critical problem - condensation . . . . Years ago (~1980), I saw the same paradox; all that heat going out the wall when it could be used to heat the house (I was living in East Lansing Michigan). So, I rigged up a serpentine set of aluminum pipes (exhaust dryer vent material) with two 90 degree elbows to make a 180 degree turn. One end connected to the electric dryer vent outlet and the other went out to the wall outlet. I must have had five or six of the exchange tubes with maybe a dozen 180 degree turns. All mounted on the wall horizontally with stand offs above the washer dryer. The total length of pipe was perhaps 50 feet. It looked great, so pretty and shiny and I was SO proud of my skills and ability to save $ . . . I blew air from the house air handler system across the wall mounted aluminum heat exchanger and it worked GREAT!! The amount of heat dissipated was superb with about a 30-40 F decrease in the temp measured at the dryer outlet part of the exchange tube to where it exited the wall. But then reality kicked in. Despite being careful to change the lint filter, my beautiful shiny heat exchanger began to accumulate lint. And yes, the lint stuck to the insides of the aluminum pipe and the heat performance began to degrade terribly . Then one day, it began leaking water and that dripped on a clean stack of dried clothes. New baby in the house and Momma was NOT happy . Turns out, the temperature humidity relationship of a dryer is rather strict. The air going out is quite saturated with water vapor for that temperature. Decrease the temp and the moisture in that dryer air WILL condense out. The year before I had put a "heat reclaimer" on the woodstove stack and it accumulated tremendous amounts of creosote (for exactly the same reasons). So, I have given up on reclaiming dryer heat and instead have put washer/dryer in a sealed room with an outside air vent (for makeup air). I used an outside door for the room entry with good neoprene gaskets and a good sweep seal so the door sealed quite well. The make up air vent (6 inches) comes down from the attic and I put a filter over the open end in the attic. This works REALLY well. Nobody sees it but I remain proud of the savings nevertheless . Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990 Last edited by stevehull; 09-16-13 at 04:30 PM.. |
06-04-14, 12:07 PM | #96 |
Andy
Join Date: Jun 2014
Location: SW VA
Posts: 45
Thanks: 6
Thanked 13 Times in 10 Posts
|
Great thread.
I've been thinking of use our dryer exhaust for preheating our hot water, something we need whether winter or summer. There are 'condensing' or 'ventless' dryers that use either recirculated room air or tap water in a heat exchanger to dry clothes. Unfortunately the water is typically wasted. My thought is to preheat our 50 deg. F well water in a heat exchanger connected to the dryer. The water/heat would then be stored in a separate tank that feeds into our water heater. I could add an air-to-water heat exchanger to our existing electric dryer exhaust and then somehow plumb/pump the water to the preheat tank. Thought I'd shared to get a sanity check. |
01-24-15, 12:18 PM | #97 |
Renewable Energy Nut
Join Date: Jul 2011
Location: Winnipeg, Manitoba, Canada
Posts: 42
Thanks: 17
Thanked 20 Times in 9 Posts
|
Anyone come up with new ideas for this yet? I'm replacing my old flex hose with new ducting today. The old white plastic ribbed stuff has cracked, is full of lint dust and had a kink at the top of the run to the outside. Really bad install. I'm surprised it's taken me this long to replace it. I should see a savings just from a proper run allowing quicker drying times.
|
01-24-15, 06:41 PM | #98 |
Apprentice EcoRenovator
Join Date: Apr 2011
Location: PNW
Posts: 197
Thanks: 0
Thanked 47 Times in 31 Posts
|
Simplest is best, esp in colder climate where you can use the added indoor humidity.
I simply route the dryer vents (have 2 dryers) to a box with a furnace filter, dump the heat right back into the room - work with electric dryers only for obvious reasons. Never had had a problem with high humidity or condensation. Dryers are in the basement, more sawdust down there than anything that would get past the furnace filters. Summertime: solar dryer outside <G> |
The Following User Says Thank You to mejunkhound For This Useful Post: | pletby (01-24-15) |
01-25-15, 08:01 AM | #99 |
Andy
Join Date: Jun 2014
Location: SW VA
Posts: 45
Thanks: 6
Thanked 13 Times in 10 Posts
|
I ended up going a different way for now. I found a used Bosch Axxis clothes dryer, fixed it up, and installed it in the same area where our heat pump water heater (Geospring) is. Theoretically, at least some of the hot dry air exhausted by the dryer is used to heat our water.
I was very happy to close off the outside dryer vent. Last edited by Semipro; 01-25-15 at 09:51 AM.. |
01-25-15, 08:36 AM | #100 |
Supreme EcoRenovator
|
Super awesome! Not only are you keeping the heat, you are also reusing someone else's rubbish. Surprises like this is why I read these stories.
Quest, i have a favor to ask of you. After you have a little experience with this condensing dryer, can you please writeup a short review? Lots of fellow members are asking questions about these machines. Many are on the fence as to the quality vs energy savings vs running time etc. The electric toaster and gas burner dryers have a headlock on the market. Many would-be buyers are not convinced these units really work. Much less work well or for long. Edit: thanks for the write up sir. Didn't expect ot so fast. Last edited by jeff5may; 01-25-15 at 06:14 PM.. |
The Following User Says Thank You to jeff5may For This Useful Post: | Semipro (01-25-15) |
Tags |
dryer, heat recovery |
Thread Tools | |
Display Modes | |
|
|