EcoRenovator  

Go Back   EcoRenovator > Improvements > Renovations & New Construction
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 10-05-16, 07:59 PM   #581
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

Good concern Randen
I probably have twice as much pex per square foot as what u used (6" OC)
The state of Colorado rural counties inspector (Andy Clark) inspected it before insulation & Sheetrock.
He was impressed & said that it was "over radiated & probably wouldn't need over 140*F water to heat it" I think 170*F AWT will probably be needed at design temp.

It is getting down in the teens at night there now & it's doing fine.

The system is of my own design that I call "Buffer Centric"

There is a large Rheem ST120 DHW / buffer tank, it serves both functions.
The temperature of the tank is controlled by an ODR Tekmar 256, it ranges from 140* +- 15* when its above 60* outside, up to 170* +- 15* when its -20* outside.

In between the boiler & the tank is a GEA Flat 30 plate 5" x 12" heat exchanger.

When the Tekmar 256 tells the boiler to fire, 2 pumps come on, one on each side of the heat exchanger. Heat moves from the boiler into the tank.

During this the System pump (Grundfos Alpha) can be on or off depending on if any Ecobee3 thermostat is calling for heat.

Buffer tank mode:
If the system calls for heat after after the tank is up to the required temperature
& the boiler is off, heat will be pulled out of the tank and flow in the opposite direction through the heat exchanger to the system.

I had a system like this in my house for the last 3 years & now one is in my Sons new house.

buffalobillpatrick is offline   Reply With Quote
Old 10-05-16, 10:18 PM   #582
randen
Uber EcoRenovator
 
Join Date: Apr 2011
Location: Strathroy Ontario Canada
Posts: 658
Thanks: 9
Thanked 192 Times in 130 Posts
Default

Buffalobillpatrick

I wish that it performs well. You have experience with your home this is good. My experience was much different. I hated ripping it out for a re-do. But the ultimate result is superlative.

In another thread there has been some conjecture that you wouldn't be able to discern a heated floor. To keep a room temp of 21 Deg.C. the floor will be warmer to give up its heat load to the cooler air above. Therefore the sensation of a warm tile against your foot as you roll out of bed on a blustery winter morning is what you will revel in.

Randen
randen is offline   Reply With Quote
The Following User Says Thank You to randen For This Useful Post:
buffalobillpatrick (10-06-16)
Old 10-06-16, 12:23 AM   #583
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,431
Thanks: 431
Thanked 619 Times in 517 Posts
Send a message via Yahoo to jeff5may
Default

BBP,

Egad, that's 10 tons of heating! In Crested Butte, I don't doubt you will probably need it in a couple of months. It would sure suck to be cold all winter way up there. Please let us know how the house does.
jeff5may is offline   Reply With Quote
The Following User Says Thank You to jeff5may For This Useful Post:
buffalobillpatrick (10-06-16)
Old 10-06-16, 05:28 PM   #584
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

My last house that I just sold was insulated very well & had great Windows.
When it was 0*f outside the floors were only 75*f to maintain rooms at 70*f
So about 10btu/ft2
Never had the warm floor feeling, always had to wear warm house slippers.
buffalobillpatrick is offline   Reply With Quote
Old 10-06-16, 05:32 PM   #585
buffalobillpatrick
Master EcoRenovator
 
Join Date: Mar 2014
Location: Florissant, Colorado
Posts: 599
Thanks: 814
Thanked 59 Times in 55 Posts
Default

In my Sons new house, I think the floors will need to be about 85*f when it's -20*f outside.
It's insulated well, but had lots of huge Windows
buffalobillpatrick is offline   Reply With Quote
Old 11-16-16, 03:52 PM   #586
jasonvan
Lurking Renovator
 
Join Date: Nov 2016
Location: BC, Canada
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default Any way to get Vlad's diagram?

This thread is great. I'm planning a similar system to Vlad. Unfortunately the images he posted in 2012 no longer show up. Is there a way that I can see this pumping and electrical diagram?

Quote:
Originally Posted by Vlad View Post
Here is the plumbing diagram and very basic electric diagram. If you have any questions ask them I will post more details.

jasonvan is offline   Reply With Quote
Old 11-20-16, 09:07 PM   #587
AC_Hacker
Supreme EcoRenovator
 
AC_Hacker's Avatar
 
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
Default

This is a really big problem.

A HUGE amount of posts and information have been volunteered on EcoRenovator, and they should all be accessible. But they are not. Some people post their images here on the ER site, and they seem to remain available. Other people post images on second-party sites, and the chances of long term availability go out the window.

jasonvan,

Can you post the link where Vlad's images should have been?

I might be able to retrieve them for you.

Some small amount of EcoRenovator is available on Internet Archive.

If that fails, I may be able to contact Vlad. Geo_EN_Gee & I drove up to Canada to see his setup. I may still have his phone number. Maybe Geo_NR_Gee has it.

We'll do what we can for you.

-AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker...
AC_Hacker is offline   Reply With Quote
Old 11-20-16, 09:31 PM   #588
Geo NR Gee
Journeyman EcoRenovator
 
Join Date: Jan 2011
Location: Seattle
Posts: 326
Thanks: 109
Thanked 23 Times in 18 Posts
Default

Here are some pictures from that visit.











Attached Thumbnails
Click image for larger version

Name:	IMAG1981.jpg
Views:	2417
Size:	198.4 KB
ID:	7398   Click image for larger version

Name:	IMAG1980.jpg
Views:	2459
Size:	194.4 KB
ID:	7399   Click image for larger version

Name:	IMAG1979.jpg
Views:	2406
Size:	99.3 KB
ID:	7400   Click image for larger version

Name:	IMAG1985.jpg
Views:	2479
Size:	164.5 KB
ID:	7401   Click image for larger version

Name:	IMAG1986.jpg
Views:	2447
Size:	157.4 KB
ID:	7402  

Click image for larger version

Name:	IMAG1978.jpg
Views:	2446
Size:	78.8 KB
ID:	7403  
Geo NR Gee is offline   Reply With Quote
Old 11-20-16, 09:41 PM   #589
Geo NR Gee
Journeyman EcoRenovator
 
Join Date: Jan 2011
Location: Seattle
Posts: 326
Thanks: 109
Thanked 23 Times in 18 Posts
Default

Our very own AC Hacker


Drilling rod




Vlad and his drill rig



Attached Thumbnails
Click image for larger version

Name:	IMAG1987.jpg
Views:	2367
Size:	142.2 KB
ID:	7404   Click image for larger version

Name:	IMAG1988.jpg
Views:	2323
Size:	88.9 KB
ID:	7405   Click image for larger version

Name:	IMAG1989.jpg
Views:	2252
Size:	113.7 KB
ID:	7406   Click image for larger version

Name:	IMAG1990.jpg
Views:	2489
Size:	150.4 KB
ID:	7407   Click image for larger version

Name:	IMAG1994.jpg
Views:	2317
Size:	124.0 KB
ID:	7408  

Geo NR Gee is offline   Reply With Quote
Reply


Tags
diy, heat pump, hydronic, pex, radiant

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:43 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design