EcoRenovator  

Go Back   EcoRenovator > Improvements > Solar Power
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 04-05-16, 12:05 PM   #1
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Smile 12V Community Garden Sign - Need help with calculations.

Hello all, nice to be here on this forum!

I fabricated a large metal sign for our community garden. ( Looks pretty cool if I must say so myself. )

Behind the sign I placed 200 - 5630 LED modules from ebay. Total of 600 LEDS



What I have purchased

200 - 5630 LED Modules ( 3 LEDs each, 600 LEDS total )

1 - Kyocera KD140GX-LFBS 140 Watt 12 Volt Solar Module

1 - Car battery

1 - Solar Charge Controller 12V



I need help with equipment and following questions...

1. What percent of battery will I use up if LED lights turn on for 5 hours? ( I understand you should draw less than 50% of battery for long life )
2. Should I get a deep cycle marine battery?
3. What battery would you recommend for regular use charging/discharging 600 - 5630 LEDs for 5 hours every evening?
4. Comparison running brighter 600-5630 LED modules VS 600- 3528 LED modules? What is power, current draw difference?
5. Do you recommend any other equipment? ie. Solar panel, battery, charge controller.


Thank you for your help!

stevef22 is offline   Reply With Quote
Old 04-05-16, 12:43 PM   #2
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
Default

All we need to know is how many watts each LED module uses. That will be on the eBay site.

A deep cycle (aka "marine") battery will be needed. Once we know the total wattage draw (LED module times 200) , then you multiply that by 5 to bet a panel wattage. From that, we now the current to purchase a battery charge controller.

Another way to figure out the current draw is to hook up the LEDs to an existing car battery and place a cheap current meter (standard "voltmeter" type of instrument) in series. Use the DC current setting. This will tell you the circuit current for that number of LED modules.


Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Old 04-05-16, 01:02 PM   #3
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Found specs on ebay ads for both 3528 and 5630 LEDS

5630
0.72W per string = 3 LEDS

3528 per string = 3 LEDS
0.3W

So if I have 600 LEDS...

0.72W = 432Watts
0.3W = 180Watts

Am I correct on this?


LED Quantity: 3 5630SMD leds per string
Color: Warm White
Color Temperature: 3000-3500K
Output power: 0.72W per string
REMARKS: *20pcs means 14.4W, to power up 20pcs you will need a 1.2A DC power supply which is not included in this listing.*
( DO NOT connect led directly to 110v outlet use only 12V AC power supply)
Protection Rate IP65(Waterproof)
Adhesive fixed: double-sided adhesive*Adhesive is for first step fixation, to permanately fix the strings you will need extra fiber glues.*
Interface definition: AWG 20 # wire, gray is positive, white for the negative
Standard cascade: 20PCS
Shell material: PVC plastic material
Sing String Size: 75(L)*12(W)*2.5(H) mm

---------------------

Specifications:
Type:Module 3 LED 3528 SMD
Optional color:Cool White
LED quantity: 3PCS
Beam angle: 120 °
Light Source Life: 50.000H
Working voltage: DC12V
Power: 0.3W
Adhesive fixed: double-sided adhesive
Shell color: white
Size: (about)7.8cm*1.5cm*0.5cm
Standard cascade: 20pcs
Shell material: PVC plastic material
-----------------------------
stevef22 is offline   Reply With Quote
Old 04-05-16, 01:51 PM   #4
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
Default

Humm, confusing technical data. Hook a set up to a 12 V battery and measure current.

Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Old 04-05-16, 02:37 PM   #5
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Smile

Ok I figured it out now


144 Watts for 5630LEDS total

60 Watts for 3528LEDS total

I can use 3520 LEDS ( Dimmer but less than half wattage)

What battery would you recommend for 5 hours of run time every evening?
stevef22 is offline   Reply With Quote
Old 04-05-16, 03:44 PM   #6
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
Default

I am confused. When all the LEDs are powered up, what is the total wattage of ALL 200 LED modules . . .?

(144 or 60 watts)?

What size battery did you buy (amp hours) and what amperage solar controller? The solar panel might produce an average of 100 watts but a 12 V solar panel will not charge a 12 v battery. The panel needs to be a higher voltage. Put the panel in the sun and measure the voltage output.

Or - on the back of the panel, it may say what the short circuit voltage is.


Steve




Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Old 04-05-16, 04:05 PM   #7
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Default

sorry for that, I tend to confuse myself often enough.


I have ordered both types of LEDS and can use one or the other or both on my project,


The 5630LED strip draws 144 Watts total.

The 3528LED strip draws 60 Watts total.

so Im forgetting about the 5630LED strip and going with 3528LED strip.


So I have a 60Watt total need for 5 hrs every night.

What batteries, solar panel and charge controller would I need?
stevef22 is offline   Reply With Quote
Old 04-05-16, 05:30 PM   #8
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 826
Thanks: 241
Thanked 165 Times in 123 Posts
Default

In your very first post, you said you have already purchased a 140 watt PV panel, car battery and charge controller.

Need specifics on what you have purchased.


Steve
__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Old 04-05-16, 05:46 PM   #9
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Please take a look at this drop box folder. I took a picture of back of Solar Panel and solar controller. My battery is standard 12V car battery ( probally will need to change )

Up too 4 posts, will be able to link next post.
stevef22 is offline   Reply With Quote
Old 04-05-16, 05:47 PM   #10
stevef22
Lurking Renovator
 
Join Date: Apr 2016
Location: San Antonio Texas
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Here is link

https://www.dropbox.com/sh/69hldv2hl...xIK8skgWa?dl=0

stevef22 is offline   Reply With Quote
Reply


Tags
12v, community, sign

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:02 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design