gshp in florida ac only - Page 6

rhino 660 · 02-16-12, 08:14 PM

priming the loops

i got my heatpump FHP 2 ton with ECM blower

and some solar goodies outback vfx3648 3600 watts 48V grid tied battery backup inverter, outback fm80 80A charge controller, and midnight solar's combiner box. got this as a bonus from my boss.

im going to run 4kw dc to it

i drew up some plans for doing a ground mount

rhino 660 · 02-16-12, 09:26 PM

while priming my loops the temp gauge remained at 72*F

rhino 660 · 02-19-12, 11:05 PM

i built ducting out of 3/4'' foam board, i just have to finish a 15' run in the attic

rhino 660 · 02-19-12, 11:06 PM

rhino 660 · 02-19-12, 11:18 PM

i ordered some more parts for my priming setup. what im going to do is hook everything up minus the loop pump and use a ball valve to choke down the priming pump output to 8 gallons a minuet and check the pressure at the pump output from there i can perfectly size the circulator pump needed

Xringer · 02-19-12, 11:26 PM

Man, that's one busy weekend! Very Nice work on the duct-work!!
Looks like you are going be making the power to run that system too..

rhino 660 · 02-20-12, 12:00 AM

yes lots of work im also doing solar hot water after i finish these to projects after all that stuff i should have no power bill

rhino 660 · 03-05-12, 09:22 AM

i finished all the ducting this is the attic portion

i allmost have all the fittings i need to check the head pressure

creeky · 03-05-12, 04:44 PM

nice set up. look forward to seeing more.

rhino 660 · 03-05-12, 08:27 PM

thank you i got antsy and decided to test run my unit with the priming pump, i got great results. i wired the loop pump into the compressor relay.
thermostat i stole off my wall

this is the pressure with the pump at full blast

heating mode temp return from loopfeild

heating mode temp to loopfeild

cooling temp return from loopfeild

cooling temp to loopfeild

i just need to devise a scheme to measure the gpm and then check the pressure so i can get a proper pump

02-19-12, 11:26 PM	#56
Xringer Lex Parsimoniae Join Date: Feb 2009 Location: Woburn, MA Posts: 4,918 Thanks: 114 Thanked 250 Times in 230 Posts	Man, that's one busy weekend! Very Nice work on the duct-work!! Looks like you are going be making the power to run that system too.. __________________ My hobby is installing & trying to repair mini-splits EPA 608 Type 1 Technician Certification ~ 5 lbs or less..

02-16-12, 08:14 PM	#51
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	priming the loops i got my heatpump FHP 2 ton with ECM blower and some solar goodies outback vfx3648 3600 watts 48V grid tied battery backup inverter, outback fm80 80A charge controller, and midnight solar's combiner box. got this as a bonus from my boss. im going to run 4kw dc to it i drew up some plans for doing a ground mount

02-16-12, 09:26 PM	#52
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	while priming my loops the temp gauge remained at 72*F

02-19-12, 11:05 PM	#53
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	i built ducting out of 3/4'' foam board, i just have to finish a 15' run in the attic

02-19-12, 11:06 PM	#54
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts

02-19-12, 11:18 PM	#55
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	i ordered some more parts for my priming setup. what im going to do is hook everything up minus the loop pump and use a ball valve to choke down the priming pump output to 8 gallons a minuet and check the pressure at the pump output from there i can perfectly size the circulator pump needed

02-20-12, 12:00 AM	#57
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	yes lots of work im also doing solar hot water after i finish these to projects after all that stuff i should have no power bill

03-05-12, 09:22 AM	#58
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	i finished all the ducting this is the attic portion i allmost have all the fittings i need to check the head pressure

03-05-12, 04:44 PM	#59
creeky Journeyman EcoRenovator Join Date: Jun 2011 Location: a field somewhere Posts: 304 Thanks: 64 Thanked 44 Times in 31 Posts	nice set up. look forward to seeing more.

03-05-12, 08:27 PM	#60
rhino 660 Apprentice EcoRenovator Join Date: Oct 2010 Posts: 105 Thanks: 0 Thanked 10 Times in 8 Posts	thank you i got antsy and decided to test run my unit with the priming pump, i got great results. i wired the loop pump into the compressor relay. thermostat i stole off my wall this is the pressure with the pump at full blast heating mode temp return from loopfeild heating mode temp to loopfeild cooling temp return from loopfeild cooling temp to loopfeild i just need to devise a scheme to measure the gpm and then check the pressure so i can get a proper pump