EcoRenovator  

Go Back   EcoRenovator > Improvements > Conservation
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 02-21-10, 09:18 AM   #1
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default DIY ventilation heat exchanger

I am thinking more and more about our upcoming renovation, a part of which will hopefully be redoing our ventilation system. One of the things that would greatly increase the efficiency of the new setup is an air-air heat exchanger (recuperator). The ones I've seen here cost the equivalent of US$2000-2500, which seems a lot. Does anyone know how easy it would be to build one at home?

I found a local forum (in Polish) where someone was planning to make one. The plan was for a 120cm long countercurrent heat exchanger, with 200mm or 250mm diameter input/output and 25m^2 of exchange area. The calculations for the number of sheets of thin steel (later copper or aluminum) needed came to a cost of 60%-70% of a factory-made unit, plus random parts, machinery, at least a whole week of time, etc. The whole thread was 60 pages long, with 50 posts/page, and a change in design every 5 posts, so I gave up after the second page and have no idea if the project ever got off the ground. No pictures in that thread (or only for registered users).

Any ideas on how to go about making a more or less efficient (60+%) heat exchanger? Pictures/drawings of the insides of different types would be nice, as would a cost vs. efficiency comparison.

Piwoslaw is offline   Reply With Quote
Old 02-21-10, 12:35 PM   #2
Ryland
Master EcoRenovator
 
Join Date: Mar 2009
Location: Western Wisconsin.
Posts: 913
Thanks: 127
Thanked 82 Times in 71 Posts
Default

It would draw a bit more energy but you could build one with an air conditioner that in the winter cools the warm outgoing air before it leaves the house and warms the incoming air, in cool weather this could be enough to keep the house warm and in warm weather it might be enough to keep the house cool.
otherwise the inside of heat exchangers that I've installed have what looks like coroplast... might even be coroplast but it should be something more conductive.
Ryland is offline   Reply With Quote
Old 02-21-10, 02:33 PM   #3
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default

Thanks Ryland A small air-air heat pump (like an old A/C unit) could be hooked up after the heat exchanger, increasing the amount of heat transfered, or reducing the temp difference on both sides of the AC, depending on how you look at it. In fact, there will already be a heat pump in the system we are planning, it will transfer heat from waste air to the hot water tank. That will be the first step, the second - a heat exchanger for intake/waste air, and finally a ground source heat exchanger to preheat (precool in the summer) before the recuperator.

I looked around and found a few pics. Here is the inside of a cross-flow recuperator:



And here is how it works:



Here is a homemade plywood construction that uses 2 cross-flow recuperators in a counter-current set-up (increasing efficiency):



Here's the inside of a large area, counter-current heat exchanger:



It is made of scores of thin sheets of copper or aluminum, stacked 4-5mm apart. The space in between sheets is closed off at every other end (let's call them even) at one end and odd ends at the other. That way the two airstreams don't mix, but exchange heat over an area equal to the area of all of the sheets (minus 2). This is very efficient, but large, heavy and expensive. On the other hand, if space isn't a problem, and the cost is not more than a commercial heat exchanger, then the higher efficiency may make this option worth while.

Here is a pictures of someone's finished project:



You can see the smaller diameter bypass for when you do not want to lose/gain heat.

An idea I got while looking through these projects was to use a long length of thin, flexible tubing inside a larger diameter, insulated tube (like Ben's DIY Solar Hot Water Heat Exchanger). This could be a temporary solution, until a better heat exchanger could be made/installed, after which the tubes could be reused in the house's ventilation system or as a ground source heat exchanger.
Attached Thumbnails
Click image for larger version

Name:	2_1241387613.jpg
Views:	80410
Size:	38.2 KB
ID:	605   Click image for larger version

Name:	4af30626d6d622d0755c1540a46aaa13.jpg
Views:	72448
Size:	48.5 KB
ID:	606   Click image for larger version

Name:	ekspert-budowlany-rekuperatory-co-warto-wiedziec1.jpg
Views:	76112
Size:	18.5 KB
ID:	607   Click image for larger version

Name:	639222610996f8ffa76111d8dad5145f,5,19,0.jpg
Views:	83491
Size:	9.9 KB
ID:	608   Click image for larger version

Name:	4d4fddd2a945955e.jpg
Views:	78893
Size:	75.9 KB
ID:	609  

Piwoslaw is offline   Reply With Quote
The Following User Says Thank You to Piwoslaw For This Useful Post:
poorwill (06-16-21)
Old 02-21-10, 10:12 PM   #4
Heynow999
Lurking Renovator
 
Join Date: Feb 2010
Location: Toronto
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I have always thought it would be a good idea to vent your bathroom exhaust and dryer through on of these. Perhaps you could vent the bathroom full time, and the the dryer only during the heating season.
Heynow999 is offline   Reply With Quote
Old 02-22-10, 12:41 AM   #5
Ryland
Master EcoRenovator
 
Join Date: Mar 2009
Location: Western Wisconsin.
Posts: 913
Thanks: 127
Thanked 82 Times in 71 Posts
Default

Quote:
Originally Posted by Heynow999 View Post
I have always thought it would be a good idea to vent your bathroom exhaust and dryer through on of these. Perhaps you could vent the bathroom full time, and the the dryer only during the heating season.
Panasonic makes one that is part of a bath vent fan, but if it gets to cold of air coming in to it from the out doors it bypasses the heat exchanger to prevent freeze up, around 20F or 25F if I remember correctly.
Dryers need to have the lint removed first or they will clog it.
Ryland is offline   Reply With Quote
Old 02-28-10, 05:12 PM   #6
AC_Hacker
Supreme EcoRenovator
 
AC_Hacker's Avatar
 
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
Default ERV, HRV, de-humidifier hack...

Quote:
Originally Posted by Piwoslaw View Post
Any ideas on how to go about making a more or less efficient (60+%) heat exchanger? Pictures/drawings of the insides of different types would be nice, as would a cost vs. efficiency comparison.
Piwoslaw,

Here's a URL for a DIY Heat Recovery Ventilator:

Make - Volume 18

* * *

The photos I see of Heat Recovery Ventilators usually use a cross-flow cell, with the air paths crossing at a 90 degree angle. They usually have an efficiency of about 60% to 70%. I have seen write-ups of experiments done on cells that had a 180 degree cross-flow and the efficiency was increased to some degree (maybe 5% to 8%). Sorry, but I didn't book mark the studies.

There's also a wheel type that claims efficiency up to 90%. Here's an example:

Heat Exchangers Energy Recovery Ventilator Air

Additionally, there's a heat pipe HRV, but I don't see very many Internet references to that type, but here is one:

Computer Environment, Inc. Website

Here's a page with a pretty good overview of the topic:

SustainableSources.com: Energy Recovery Ventilator

It looks like the need for and success of a HRV/ERV are based on having a very tight house...

* * *

Regarding the 90 degree cross-flow types, if my understanding is correct, there are Heat Recovery Ventilators (HRV) and then there are Energy Recovery Ventilators (ERV), the difference being that the ERV uses a water permeable membrane to allow outgoing air condensed moisture to be used to re-humidify the incoming air.

I have seen a page that represented various Chinese companies, that listed just the cross-flow cells of various sizes. I tried to locate that URL for this post but was not able to find the page I remembered. But I'm pretty sure that the cells for most, if not all of the ERVs made in the US and probably also Europe are manufactured in China, and put into locally made boxes. I have seen the completed units coming from China:

Here

Here also

* * *


In this photo is the de-humidifier someone left on my front porch, minus the plastic & steel covers.

The way it works is air is drawn through the evaporator coils, where it is chilled and frost forms and then passes through the condenser coils, where the air is warmed back up. There is a sensor on the evaporator coil and when it senses that the evaporator is likely to be full of frost, the compressor stops for a few minutes, the frost melts to water that goes into a bucket.

But the evaporator core and the condenser core are made separately, and are attached by sheet metal screws. With a little bit of luck and some very gentle handling, the cores can be separated, with the refrigeration lines intact. Then incoming air could be made to pass through an air filter and then through the condenser (hot) and into the house, while outgoing air would be made to pass through an air filter and then through the evaporator (cold) and out to the world.

Thus, the hacked de-humidifier would extract heat from the air that is exiting the house, and then return that heat to the air that is entering the house.

This is a hack that is begging to be done!

Regards,

-AC_Hacker
Attached Thumbnails
Click image for larger version

Name:	dehumidifier-pic.jpg
Views:	85857
Size:	52.6 KB
ID:	614  

Last edited by AC_Hacker; 02-28-10 at 05:18 PM..
AC_Hacker is offline   Reply With Quote
The Following 3 Users Say Thank You to AC_Hacker For This Useful Post:
abogart (01-18-12), ELGo (04-22-13), jeff5may (02-09-21)
Old 03-01-10, 12:53 AM   #7
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default

Thanks for all the info, AC
I'm on the lookout for an old A/C (window) unit already, and thanks to you I realized that a dehumidifier would also work (I actually know how a dehumidifier works, but somehow the think processes didn't get there yet), so I'll look for one of those too.

Now I'll sift through all those links...
Piwoslaw is offline   Reply With Quote
Old 03-01-10, 08:09 AM   #8
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default

Those are some GREAT links AC Hacker! Thanks. I really like that Make article. Although, I do think it would be more efficient if it had flow going like the commercial units that use 90 degree cross flow. I'd imagine that it just makes better use of the sheet metal between the intake/exhaust. Do you have any examples of the 180 degree flowing design? With only a small amount of modification I think you'd really have a nice heat exchanger, and it could be made CHEAP too.
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Last edited by Daox; 03-01-10 at 08:41 AM..
Daox is offline   Reply With Quote
Old 03-01-10, 12:17 PM   #9
AC_Hacker
Supreme EcoRenovator
 
AC_Hacker's Avatar
 
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
Default All Roads Lead To Rome...

Quote:
Originally Posted by Daox View Post
Do you have any examples of the 180 degree flowing design?
Daox,

I tried to find the links when I did the post, but couldn't find the web site again.

Sometimes I find material that is very interesting but not relevant to an original search. I try to bookmark as much of these surprises as I can, but some just get away. I think that's how it is with the Internet.

As I recall, the increase in efficiency for the 180 degree counter flow was small (5% to 8%). The 90 degree design seems to dominate the market, my guess is that it is pretty efficient and easy to make.

For me, the lesson to be learned is that China is making the cross-flow cells and selling them to OEMs. If we can discover the source of the cells, we can build the box ourselves.

But effectively utilizing an energy recovering ventilating system is predicated on having a home that is very tightly sealed...

This gets us back to insulation and sealing... Talk about 'all roads lead to Rome', here we are again.

Regards,

-AC_Hacker

P.S.: BTW, don't know if you saw my post on Grey Water Energy Recovery, that one is not dependent on having a tight house.

* * *
AC_Hacker is offline   Reply With Quote
The Following User Says Thank You to AC_Hacker For This Useful Post:
jeff5may (02-09-21)
Old 03-01-10, 02:30 PM   #10
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default

Quote:
Originally Posted by AC_Hacker View Post
As I recall, the increase in efficiency for the 180 degree counter flow was small (5% to 8%). The 90 degree design seems to dominate the market, my guess is that it is pretty efficient and easy to make.

For me, the lesson to be learned is that China is making the cross-flow cells and selling them to OEMs. If we can discover the source of the cells, we can build the box ourselves.
From what I read somewhere, the cross flow's efficiency is around 60%-70%, while the counter flow can get over 90%, so that may be worth fighting for. I think the differences in our sources come from different designs being tested.

I'm all for finding a source of cheap cross flow cells. Using 2 or 3 to make a counter flow set up (like in the picture in my second post) would give killer efficiency. I tried googling in both English and Polish for just the guts, but no luck, only "recuperators with alu cell". I'll ask at a local builder's forum.

Re heat pump: In my climate it's very hard to find an old A/C unit, air conditioning is just starting to be mainstream. Old refrigerators, now that's a different story. I can find one in any town, or even in any roadside ditch or forest:/ On the other hand, taking a fridge apart is illegal in Europe (environmental protection laws), so hush-hush

EDIT: I found this page on different types of heat exchangers. It's in Polish, but maybe Google Translate will help. It confirms that the cross flow exchanger's efficiency is 60%-70%, and adds that using 2 of them can be 95% efficient. Also, there is a spiral heat exchanger, which appears to be just aluminum foil rolled up into a spiral tube. The benefits are 85% efficiency and frost resistance (frost is the main enemy of cross- and counter-flow cells, requiring heating elements to keep the airflow from getting restricted).


Last edited by Piwoslaw; 03-01-10 at 03:09 PM..
Piwoslaw is offline   Reply With Quote
The Following 3 Users Say Thank You to Piwoslaw For This Useful Post:
Hv23t (12-11-12), jeff5may (02-09-21), poorwill (06-16-21)
Reply


Tags
erv, heat recovery, hrv

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:12 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design