EcoRenovator  

Go Back   EcoRenovator > Improvements > Conservation
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 06-05-18, 02:08 PM   #1
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default DIY Single axis solar panel trackers

I already have the perfect spot picked out.
Some years back my land was used as a small dairy. So sections are fenced off. I have this one particularly useless fenced off section about 120 feet long and only about 12 feet wide, running north to south and it's between my well and 60 amp sub panel that's going to send power to the well.
I was thinking about just removing that section of fence.
But now I'm thinking that I could start my first crop of solar panels in there.

I want to start putting them on trackers because I can see my self easy exceeding 9.6kw which would be the limit of back feeding my 200 amp main panel.
To upgrade could cost thousands of dollars.
I need to sit down with my 2017 code book and figure out what the options are.
9.6kw would allow me to produce around 48kwh per day. But 9.6kw on single axis trackers would allow me to produce up to around 60kwh, give or take.
If I use all the loop holes and absolutely hit the limit of single phase 200 amp service I might go to 3 phase.

I have been looking at liner actuators and solar tracker controllers and if I can build the panel mounts and and tilt rig cheap enough it could be worth it.


Last edited by oil pan 4; 06-05-18 at 03:58 PM..
oil pan 4 is offline   Reply With Quote
Old 06-05-18, 02:22 PM   #2
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,923
Thanks: 172
Thanked 564 Times in 463 Posts
Default

I was able to find a 225-amp breaker box that was the same brand as my old main box. It was just a few inches taller.
I kept my 200 amp breaker and all the other breakers.
This will allow you to feed back more amps to your main box.
Something to think about.
(Busbar Rating (A) x 1.2) - Main Breaker Rating (A) = Max PV (A)

(225 * 1.2) - 200 = 70 Amps
__________________
Current project Aquaponics system , Passive Solar Greenhouse build

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Solar Install 12.5 Kwh-
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Mini Split installs -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

EV Chevy Volt -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
pinballlooking is offline   Reply With Quote
Old 06-13-18, 08:18 AM   #3
WyrTwister
Master EcoRenovator
 
Join Date: Jun 2013
Location: USA
Posts: 543
Thanks: 6
Thanked 44 Times in 38 Posts
Default

200 amp x .8 ( for continuous duty ) = 160 amps x 240 Volt = 38,400 watts .

This is single phase , assuming 3/0 copper THHN .

200 amp 3 phase x .8 ( for continuous duty ) = 160 amps x 3 x120 Volt = 57,600 Watts .

This is 3 phase 120/208 Volt , assuming 3/0 copper THHN .

Would be slightly more for 3 phase 120/240 Volt .

Wyr
God bless
WyrTwister is offline   Reply With Quote
Old 06-13-18, 08:24 AM   #4
natethebrown
Apprentice EcoRenovator
 
Join Date: Aug 2012
Location: North Alabama
Posts: 167
Thanks: 0
Thanked 40 Times in 20 Posts
Default

How do you plan on using linear actuators? I would assume you are hoping to get a good 160 deg of travel for the panels, which I think would be hard to do with a linear actuator.
natethebrown is offline   Reply With Quote
Old 06-13-18, 09:14 AM   #5
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default

Doesn't have to be the full 160° I'm going for more like 100° of motion.
It has to be really sturdy to hold up to the wind and be really cheap or else more panels and up graded electrical service would be cheaper.

Adding real trackers that stay with the sun all day can more than double the price of the total cost of the panel install, then for all that added expense and and complexity you get 1/3 more output.
What I'm looking for is up to 20% more output for more like 10% additional cost.

Last edited by oil pan 4; 06-13-18 at 11:01 AM..
oil pan 4 is offline   Reply With Quote
Old 06-13-18, 10:38 AM   #6
jjackstone
Helper EcoRenovator
 
Join Date: Mar 2009
Location: Sacramento,Ca
Posts: 88
Thanks: 5
Thanked 32 Times in 23 Posts
Default

Don't know if this will help but there are a number of tracking ideas at this website.
Red Rock Energy Heliostats

JJ

jjackstone is offline   Reply With Quote
Reply


Tags
diy, homemade, solar, solar panel, tracker

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:46 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design