EcoRenovator  

Go Back   EcoRenovator > Improvements > Tools
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 02-03-21, 10:54 AM   #1
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default Printing one off circuit boards at home

I watch a lot of 3d printing stuff as I do a lot of 3d printing. Youtube suggested this one and I thought it was pretty cool. Not my cup of tea as I don't work with electronics much, but I'm sure some of you will like it.


__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 02-03-21, 12:49 PM   #2
pinballlooking
Super Moderator
 
pinballlooking's Avatar
 
Join Date: Jun 2013
Location: SC
Posts: 2,923
Thanks: 172
Thanked 564 Times in 463 Posts
Default

I agree Very cool.
__________________
Current project Aquaponics system , Passive Solar Greenhouse build

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Solar Install 12.5 Kwh-
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Mini Split installs -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

EV Chevy Volt -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
pinballlooking is offline   Reply With Quote
Old 02-03-21, 08:34 PM   #3
MN Renovator
Less usage=Cheaper bills
 
MN Renovator's Avatar
 
Join Date: Nov 2010
Location: Minneapolis, MN
Posts: 939
Thanks: 41
Thanked 116 Times in 90 Posts
Default

Definitely cool, I think I'll stick with layering a thick height sandwich of Proto-Pasta Electrically Conductive PLA between a print and calling a PCB. I'm seeing about 400ohms resistance over a 2 inch spread of stacked 0.16mm layer lines in a non-PCB print. It's reasonable for low voltage and not high current applications. PCB prints being flat, I'd say grab your 1mm nozzle and print at a .32mm layer height and have a pause, swap filament to conductive, you could print your multiple internal PCB layers ...or could be on the surface too, a top layer would be easiest to print, but this allows multiple layers. A large continuous print line would be most conductive. Little LED stuff and battery powered stuff often is handled well with this stuff. There are other conductive products out there, an ABS in Europe and a TPU I heard about, but I was able to pick this stuff up at a local MicroCenter. $50 for a 500 gram spool is a little spendy, but it's a premium product that generally doesn't need much laid down to do the job.

If you ever want to print with this stuff, I recommend 60c bed, 230 max print temp(225 and slowing down is better), it doesn't like being pumped fast, I use .16mm layers(0.4mm nozzle) and it prints reliably at 30mm/sec but will skip an extruder occasionally at 35. I think it might be best at a thick layer on top or embedded in print if it is PCB style. You'd probably need to slow way down for a 1mm nozzle and .32 layers though. It's slow like PETG. ..if you heat this stuff up to rush it, it WILL clog your nozzle. It also will take a few grams of material to stop staining your next prints too, Carbon Black is a little insidious. I have a glow in the dark turtle I printed that's filled with black marks in the first 5mm.

MN Renovator is offline   Reply With Quote
The Following User Says Thank You to MN Renovator For This Useful Post:
pinballlooking (02-03-21)
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:31 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design