EcoRenovator  

Go Back   EcoRenovator > Improvements > Renovations & New Construction
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 02-06-17, 02:42 PM   #1
NeilTheCop
Helper EcoRenovator
 
Join Date: Mar 2011
Location: Roswell NM
Posts: 43
Thanks: 0
Thanked 4 Times in 4 Posts
Default Purlins?

The roof on my front porch finally gave up the ghost.
After watching the leaks get progressively worse over the years I decided to fix it. Of course in my nativity I thought, just cut out the rotted sections and re-shingle, no problem.
You guessed it, the rot was so bad that I stripped off all the roofing including the pseudo repairs that previous owners had attempted, about 40 pounds of galvanized metal and the same weight in tar sealant.
Having weighted up the cost I decided to replace it all with ribbed, not corrugated metal, now the question.
After taking off the plywood/OSB mixture that was the existing substrate I'm left with the 3/4" high gap where the sheeting used to be, to tuck the new metal under the house shingles. With only a 3/4" vertical gap and the metal roofing ribs being the same height I have no room to add the extra height of a purlin, so can the metal be attached directly to the 2X4 rafters. The 2X4's are on 16" centers and 8' in length, and I intend to cross brace every 24" or so but don't intend to walk on the roof.

NeilTheCop is offline   Reply With Quote
Old 02-12-17, 10:36 PM   #2
DEnd
Apprentice EcoRenovator
 
Join Date: Nov 2011
Location: NC
Posts: 117
Thanks: 6
Thanked 26 Times in 24 Posts
Default

Yes you can attach the roofing directly to the 2x4s, assuming the roofing is thick/stiff enough. Check with the manufacturer first. The biggest issue you have is flashing however. The roof wall intersection absolutely needs to be flashed correctly. To do that correctly you will likely be removing wall shingles/siding anyway at that point it's likely not a huge task to make the room you need to add back in the roof sheathing. the positive to that is it will likely lead to a better appearance for the roof ie: much less likely to get dents in it, and a flatter appearance for the roof in general.
DEnd is offline   Reply With Quote
Old 02-13-17, 08:03 AM   #3
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,354
Thanks: 379
Thanked 593 Times in 496 Posts
Send a message via Yahoo to jeff5may
Default

There are lots of "what if's" to consider when planning the reroof. Assuming you will be installing roofing that has the ribs running parallel to the rafters, it could sag between them and look wavy. Snow and wind load capacity are also major considerations.

Besides lowering the ridge beam/ledger board, you could install flat bar or angle over the existing rafters to add horizontal strength. Naturally, each solution has its own set of advantages and challenges. If you live in a municipality where codes and permits are in play, you can always ask the building inspector whether or not a method will be allowed.
jeff5may is offline   Reply With Quote
Old 02-16-17, 11:02 AM   #4
NeilTheCop
Helper EcoRenovator
 
Join Date: Mar 2011
Location: Roswell NM
Posts: 43
Thanks: 0
Thanked 4 Times in 4 Posts
Default

Thanks guys.
It's a moot point now because after finally getting everything cleared off I found that the original 2X6 that should be attached to the ends of the house roof rafters had been removed, and the 2X4's that made up the porch had been nailed (badly) directly to them. So I demolished the old porch completely, replaced the 2X6's (which may also account for the house creaking and why my new front door never fitted right no matter how many times I adjusted it) and now have put in new 2X4's with hurricane clips and joist hangers so I'm now able to use the 1X4 purling.
Good news is that I'm now well past the "I wish I'd never started" point.

Again, many thanks

NeilTheCop is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:26 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design