EcoRenovator  

Go Back   EcoRenovator > Improvements > Tools
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 02-20-17, 12:23 AM   #11
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default

Added another 240v tool to the mix.
I converted my old Japanese air compressor from a 100v motor to 240v.
The full load amps on this motor is rated for 7.2amps. The shut off amps are at 5.5 so I'm thinking of replacing the current 5 inch pulley for a 6.

oil pan 4 is offline   Reply With Quote
Old 12-24-17, 10:44 AM   #12
WyrTwister
Master EcoRenovator
 
Join Date: Jun 2013
Location: USA
Posts: 543
Thanks: 6
Thanked 44 Times in 38 Posts
Default

To get more air ?

Wyr
God bless

Merry Christmas
WyrTwister is offline   Reply With Quote
Old 05-29-18, 11:31 PM   #13
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default

I made another convert.
I took my nissan leafs 120v "brick" charger opened it up, broke the MOV off the circuit board, took the 20vAC control transformer hooked its wires up line to neutral/ground on the 10-30 dryer cord i installed, thus converting it to 240v power.
So instead of charging at around 1.4kw, it now charges at 2.8kw.
oil pan 4 is offline   Reply With Quote
Old 05-31-18, 10:33 PM   #14
ecomodded
Supreme EcoRenovator
 
Join Date: Sep 2012
Location: Vancouver Island,Canada.
Posts: 1,037
Thanks: 116
Thanked 100 Times in 87 Posts
Default

I'm guessing the charger gets hot with 2800 watts going threw it ? also curious how many volts & AH's the battery pack is.
__________________

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
ecomodded is offline   Reply With Quote
Old 05-31-18, 11:20 PM   #15
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default

A leaf packs notmal voltage is something like 380v.
This battery pack appears to have most of its 24kw intact.
My OEM EVSE is the 2011 and 2012 "brick" that was designed and over built by Panasonic appliances.
The evse doesn't really get very warm at all, it's just a fancy extension cord with built in safety switch. The cords power circuit doesn't know if it's carrying 120 or 240v power.
The conversation from 240vAC to 300 to 400vdc happens in the vehicles built in charger.
oil pan 4 is offline   Reply With Quote
Old 06-01-18, 03:34 PM   #16
ecomodded
Supreme EcoRenovator
 
Join Date: Sep 2012
Location: Vancouver Island,Canada.
Posts: 1,037
Thanks: 116
Thanked 100 Times in 87 Posts
Default

Thanks for the info on the charge system , could be using 240v will have a higher conversion efficiency percentage then 120v well that's my guess.

Im going to try and get a grip on this here and now

For Solar panels is it best to convert to ac then to dc or is it preferable to use DC to DC with PV charge stations ?
__________________

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
ecomodded is offline   Reply With Quote
Old 06-01-18, 06:03 PM   #17
oil pan 4
Land owner
 
Join Date: Nov 2012
Location: NM
Posts: 1,026
Thanks: 12
Thanked 127 Times in 107 Posts
Default

All the charging setups I am aware of use AC input power.
The j1772 input voltage is something like 100 to 130vac for low power then 220 to 250vac for the high voltage.
Chademo sends pack voltage out to the vehicle. The lowest voltage chadomo I have seen uses 240v single phase, most use 480v 3 phase.

In theory if you had unlimited budget you could get a chademo that takes DC input and steps it up, but if your voltage is say 48vdc I imagine that the conversation inefficiencys would be fairly horrific. If you tied into say a 400 to 1,000v array the conversation would be pretty good.
oil pan 4 is offline   Reply With Quote
Old 06-10-18, 09:38 AM   #18
Elcam84
Apprentice EcoRenovator
 
Join Date: Jun 2013
Location: TX
Posts: 275
Thanks: 2
Thanked 31 Times in 24 Posts
Default

What are you using for grinding wheels? Usually its an issue with not having the best abrasive for the job.

Elcam84 is offline   Reply With Quote
Reply


Tags
220v, 240v, generator, welder

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:44 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design