EcoRenovator  

Go Back   EcoRenovator > Improvements > Conservation
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 10-30-09, 04:27 AM   #21
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default

Quote:
Originally Posted by Daox View Post
My basement is pretty small and has a real low ceiling. I'd love to hang clothes down there, but it just wouldn't be real practical. If it was just me and my wife in the house I'd try to make due with lines downstairs, but we have five others in the house right now.
We have a clotheshanger over the bathtub in the upstairs bathroom.



Each of the 6 poles has a string in it which goes through a pulley, allowing it to be lowered or raised. It doesn't impede bathing too much, especially since we usually take showers in the downstairs bathroom. The evaporating moisture helps humidify the house (and condense on the windows ).

Attached Thumbnails
Click image for larger version

Name:	clothes.jpg
Views:	6762
Size:	38.1 KB
ID:	440  
Piwoslaw is offline   Reply With Quote
Old 10-30-09, 09:47 AM   #22
fike
Lurking Renovator
 
Join Date: Oct 2009
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Daox View Post
Welcome to the site fike.

If you cool the air too much you'll get condensation. Not that you can't deal with it, but you'll have to make accommodations for it.
Thank you for the welcom.

Yea, I guess there would be condensation, but I am not sure that it would be very harmful in the long run. I would guess in 2 years or 10 years (I have no idea how long) the duct would rust out. If it is 2 years, it probably isn't cost effective. If it is 10 years, it is probably a good idea.

I also considered putting a damper switch to direct it through a short direct route in the summer months and a long and meandering route in the winter months.
fike is offline   Reply With Quote
Old 10-30-09, 09:50 AM   #23
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default

To lengthen the life of the system you could of course use aluminum ducting.

I'm not sure how bad it would be, but condensation would lead to lint build up I would think. Wet lint would hold moisture and lead to mold problems. I'm not sure how bad it would really be, but thats another thing to look out for.
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 10-30-09, 11:21 AM   #24
fike
Lurking Renovator
 
Join Date: Oct 2009
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by Daox View Post
To lengthen the life of the system you could of course use aluminum ducting.

I'm not sure how bad it would be, but condensation would lead to lint build up I would think. Wet lint would hold moisture and lead to mold problems. I'm not sure how bad it would really be, but thats another thing to look out for.
I thiink if you keep the lint filter clean, it shouldn't be a problem. The exterior vent doesn't show any buildup of lint, so I would assume it is pretty lint-free.
fike is offline   Reply With Quote
Old 10-30-09, 11:44 AM   #25
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default

You must have a cleaner/newer dryer than mine. Mine has lint all caked to the pipe walls. Not a ton, but its there.
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 12-14-09, 01:18 PM   #26
NeilBlanchard
Journeyman EcoRenovator
 
NeilBlanchard's Avatar
 
Join Date: Dec 2009
Location: Maynard, MA Eaarth
Posts: 383
Thanks: 78
Thanked 39 Times in 32 Posts
Default

Hi,

I think a large filter is the way to go, since you would recover ALL of the heat, and you would get the moisture as well. In the winter time in heated houses, the air gets very dry without some way of humidifying it.

We has a gas dryer, so maybe a carbon monoxide sensor would be a smart thing to have?
NeilBlanchard is offline   Reply With Quote
Old 12-14-09, 01:37 PM   #27
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default

Good to see you over here Neil.

If you were to vent directly into the house, I would imagine a carbon monoxide sensor would be absolutely essential. Dryers go through quite a bit of air. I don't even know if it would be possible to vent it directly into the house without major air quality problems.
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 12-14-09, 02:14 PM   #28
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 115
Thanked 250 Times in 230 Posts
Default

IMHO, dryers and gas hot water heaters could be a dangerous combo..

I noticed in my daughter's basement, a gas hot water heater with a PVC air input pipe.
There was a second PVC pipe for the warm exhaust gas.

I wondered if there was an air source for the dryer. Didn't see one.
When the electric dryer was running, it seems to be sucking air from the both the PVC pipes going to the hot water heater.
So, what comes in when the heater is burning gas, while the dryer is running? Exhaust gas?
Xringer is offline   Reply With Quote
Old 12-15-09, 03:46 PM   #29
ynot7201
Lurking Renovator
 
Join Date: Dec 2009
Location: west brome quebec canada
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I am starting to work on a system that encloses solid aluminum pipe (instaed of flex). Then surronding this with a box, and air circulating from on end to the other thus taking heat from skin of pipe .no damp air or lint problems ..I hope it works!!
ynot7201 is offline   Reply With Quote
Old 01-22-10, 11:53 PM   #30
Christ
Apprentice EcoRenovator
 
Join Date: Aug 2009
Posts: 123
Thanks: 14
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by ynot7201 View Post
I am starting to work on a system that encloses solid aluminum pipe (instaed of flex). Then surronding this with a box, and air circulating from on end to the other thus taking heat from skin of pipe .no damp air or lint problems ..I hope it works!!
This is exactly like an air to air intercooler, but will not be as efficient as a bar/plate design. Skin xfer of heat is limited to surface area, and the smaller your pipes are, the more surface area there is to xfer heat from one medium to the next. Bar and plate is one of the most efficient because there is a tradeoff between thermal xfer efficiency and pressure drop, and many of the best intercoolers on the market are borderline at 80% efficiency (of this type of design).

Also, keep in mind that the more heat you extract from your exhaust, the more you slow it down, making it more difficult for the intake fan to blow air through the dryer, and more difficult for the moisture to leave. The idea is to snake as much heat as you can right at the exhaust outlet so that there isn't a pressure increase slowing down flow.

Another way you might go about this is to minimize heat loss in all places except where you specifically want the heat to go. Insulate your exhaust and intake. If you want heat exchange from the exhaust to the intake, you don't want heat exchange anywhere else, so if you insulate the tubing, you can mitigate much of the heat loss, making the system more efficient than it would have been before, so your heat exchanger might have less of an impact on exhaust flow velocity.

Keep in mind, also, that you will need to periodically clean the heat exchange surfaces. If you don't, they will stop transferring heat. Lint is a great insulator.


Last edited by Christ; 01-22-10 at 11:58 PM..
Christ is offline   Reply With Quote
Reply


Tags
dryer, heat recovery

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:55 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design