EcoRenovator  

Go Back   EcoRenovator > Improvements > Solar Heating
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 08-21-20, 08:07 PM   #31
WillyP
Helper EcoRenovator
 
Join Date: Jul 2020
Location: Virginia
Posts: 30
Thanks: 8
Thanked 3 Times in 3 Posts
Default

Iam curious, where did you decide to place the temperature sensors in the storage tank?

WillyP is offline   Reply With Quote
Old 08-22-20, 11:12 PM   #32
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

Quote:
Originally Posted by WillyP View Post
Iam curious, where did you decide to place the temperature sensors in the storage tank?
No problem. I have it in the nearest bottom corner. I figured it would be the best place away from the heat exchanger coils. I did have a sensor at the top of the tank, but used it for the new large collector.
menaus2 is offline   Reply With Quote
Old 08-22-20, 11:37 PM   #33
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

I do have one issue that has happened twice now that is stumping me that I'm sure you guys would have some insight on.

I've had water come out of the circulation resevoir to the point the the highest pipe dumping into it has a slight air gap when I find it. There are two holes on the side of the cooler resevoir where the pipes go in that were not sealed.

It looks like the water leaked out of those holes, but they are 4-5 inches above where the pipes end. Somehow the water level rose enough to drain out, but then later the water level dropped below the discharge pipe. Then i. Guessing allowing air to enter the loop. When I noticed it today the motor was so hot it was starting to melt the insulation on it! I rechaged the loop and the pump still works fine. No sign of any leaks anywhere else. It worked solid for 2 weeks straight since the first time it happened.

To "fix" it I extended the pipes another 4-5 inches to the bottom of the resevoir. I also sealed the pipe holes with silicone. My theory is that whatever caused the water level to rise that much will have more room to expand before leaking out. Then when it contracts back down it will have to go nearly to the bottom unit the siphon breaks.

My best guess is maybe boiling occurred in a section (perhaps some weird low pressure spot?) pushing the water out of the resevoir. It then either cooled off or got pushed out, leaving the difference in volume to drop the revoir to the point the siphon was broken.
menaus2 is offline   Reply With Quote
Old 08-22-20, 11:41 PM   #34
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

How I found the resevoir. Except I had added some water. Originally the level was right below that upper pipe. You can see discoloration where the water leaked out of those holes. It's 1" pex for context.

Attached Thumbnails
Click image for larger version

Name:	20200822_190431.jpg
Views:	1766
Size:	434.8 KB
ID:	9045  

Last edited by Daox; 08-23-20 at 03:43 PM..
menaus2 is offline   Reply With Quote
Old 08-22-20, 11:47 PM   #35
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

What I did to hopefully fix it. Should more than double the amount of play in the water level height. Funny thing is that it will keep at a steady water level (usally a bit below the holes) for weeks at a time.

Attached Thumbnails
Click image for larger version

Name:	20200822_192118.jpg
Views:	1694
Size:	465.9 KB
ID:	9046  

Last edited by Daox; 08-23-20 at 03:43 PM..
menaus2 is offline   Reply With Quote
Old 10-14-20, 01:53 AM   #36
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

Just an update on the project:

1.Cut down a bunch of trees as they were starting to block the collector going into fall. More solar heat & more firewood!

2. Integrated the hot water tank with the furnace plenum heat exchanger, so I've got solar space heating. I have various thermostats & controls to make it work, but basically it has it's own dedicated thermostat in the living space and a thermostat that turns on when the tank is above 130F or so. It really blows out a good amount of heat and nice warm air. I can provide more details if anyone's interested.

3. The reservoir overflow issue has happened once since my last modification and levels stayed barely above the pipes but I think I've narrowed it down. In all circumstances the tank either reached its max temp of over 150F or the system didn't have power. So almost certainly there was boiling in the collector due to stagnation pushing the fluid out of the reservoir until it cooled enough to condense leaving the reservoir sparse. I simply refilled the reservoir with the glycol I was going to swap the water out with anyways. So the boiling point of the fluid should be higher. Also, the space heating cutting in above 130F should keep the tank below the 155F max tank temp, so the system will keep running.

Overall quite pleased so far. My electric bill is $20-25 less than last year's bills and I'm looking forward to seeing how much longer the firewood & propane lasts this winter
menaus2 is offline   Reply With Quote
The Following User Says Thank You to menaus2 For This Useful Post:
Daox (10-14-20)
Old 10-14-20, 10:22 AM   #37
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default

Great to hear. I'd love to see how you integrated the solar hot water with your furnace.
__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Daox is offline   Reply With Quote
Old 10-15-20, 09:58 AM   #38
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

Sure Daox.
Plumbing: I have a Taco style pump pulling water directly from the tank and circulating it through the furnace plenum. Kept it simple with 3/4" pex and shark bites to connect with the heat exchanger. It was conveniently left over from the outdoor woodboiler that was removed.

Controls: The heart of it is the Taco Hydro Air Fan Control (HAFC201). Its powered off the 24v furnace common with a 120vac relay for the pump and controlled by 24v thermostats terminals. When the thermostat circuit is closed it turns the fan relay on the furnace & taco pump on. Really happy with the unit.

I have 2 thermostats wired in series. One for the tank with a temperature probe and a simple thermostat in the living space. I mounted them both in the living room where I can keep an eye on the tank temp and set the living space temp easily.

FyI If you need a bulb well for temperature probe, some 1/2 pex, brass plug and silicone work great!
menaus2 is offline   Reply With Quote
The Following User Says Thank You to menaus2 For This Useful Post:
Daox (10-15-20)
Old 10-15-20, 10:03 AM   #39
menaus2
Apprentice EcoRenovator
 
Join Date: Feb 2011
Location: Driftless Region, North America, Earth, Solar System, Orion Arm, Milky Way Galaxy,Virgo Supercluster
Posts: 116
Thanks: 13
Thanked 35 Times in 25 Posts
Default

Picture of what I'm talking about.










Attached Thumbnails
Click image for larger version

Name:	20201014_171253.jpg
Views:	1732
Size:	485.5 KB
ID:	9064   Click image for larger version

Name:	20201014_171240.jpg
Views:	1716
Size:	497.6 KB
ID:	9065   Click image for larger version

Name:	20201014_171318.jpg
Views:	1746
Size:	488.7 KB
ID:	9066   Click image for larger version

Name:	20201014_171338.jpg
Views:	1693
Size:	479.5 KB
ID:	9067   Click image for larger version

Name:	20201015_083421.jpg
Views:	1707
Size:	507.0 KB
ID:	9068  


Last edited by Daox; 10-15-20 at 11:52 AM..
menaus2 is offline   Reply With Quote
Reply


Tags
heating, pex, solar, thermal, water

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:04 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design