EcoRenovator  

Go Back   EcoRenovator > Improvements > Geothermal & Heat Pumps
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 03-25-19, 01:43 PM   #1
Ron342
Apprentice EcoRenovator
 
Join Date: Feb 2010
Location: Maryland
Posts: 120
Thanks: 26
Thanked 12 Times in 8 Posts
Default Anyone good with house wiring diagnosis?

Yesterday a 120v breaker tripped in our bedroom circuit with very little connected. No recent construction efforts i can figure to cause it so unplugged everything, still trips so looked into the boxes.
First one i looked at had a socket and branched out in 2 directions from there.
s
Separated the 3 blacks, tried the breaker, no trip, located one black as the hot then read resistance between the black of each branch circuit and the still ganged together whites and also to the grounds. Both read high open circuits (megohms)
Then connected one branch black to the hot black, no trip, but when i tried the hot to the other branch black it tripped big.
What am i missing here? how can it trip on one branch if both branches are reading as open circuits between the blacks and ganged whites and grounds?
Case of your favorite beer (within reason) delivered as a reward!!

Ron342 is offline   Reply With Quote
Old 03-25-19, 02:45 PM   #2
MN Renovator
Less usage=Cheaper bills
 
MN Renovator's Avatar
 
Join Date: Nov 2010
Location: Minneapolis, MN
Posts: 939
Thanks: 41
Thanked 116 Times in 90 Posts
Default

Intermittent connection or it might need voltage to bridge a gap and start an arc. At lease you've figured out which side of the branch is causing the dead short allowing you to leave it disconnected while you trace where it's going and find out where the electrical gremlin is.
MN Renovator is offline   Reply With Quote
The Following User Says Thank You to MN Renovator For This Useful Post:
jeff5may (03-25-19)
Old 03-25-19, 10:23 PM   #3
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,428
Thanks: 431
Thanked 619 Times in 517 Posts
Send a message via Yahoo to jeff5may
Default

I agree, AC isn't as well behaved as low voltage DC. At least you seem to have a line that's staying how is. Much easier to get rid of that way. It all depends on how the defect came to be as far as the cause. Overloading causes different problems than loose or uninsulated connections. Since the branch is tripping the breaker, there should be some evidence to prove it once you find the issue. Arc Burns or melted insulation or something similar.
jeff5may is offline   Reply With Quote
Old 03-26-19, 07:48 PM   #4
philb
Apprentice EcoRenovator
 
Join Date: Nov 2010
Location: Oklahoma City
Posts: 155
Thanks: 58
Thanked 17 Times in 14 Posts
Default

If you have any GFI or arc fault plugs, check those out. The GFCI's have given me problems thats hard to trace. Replace them or take them out of the circuit.

philb is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:18 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design