EcoRenovator  

Go Back   EcoRenovator > Improvements > Renovations & New Construction
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 05-06-16, 10:25 PM   #1
nibs
Apprentice EcoRenovator
 
Join Date: Jun 2010
Posts: 206
Thanks: 1
Thanked 18 Times in 17 Posts
Default Asphalt covered styrofoam

Have a line on 4inch thick 2ft X 4ft high density blue styrofoam (probably roofmate) price is about $3 per pc ($12 per full sheet) Canadian or $9.60 us. Thirty cents US per sq ft.
It was used on a roof and covered both sides with hot tar.
I want to use it to insulate under a 2 inch floor slab with hydronic heat tubes.
The construct will be something like
water proof membrane,
1 or 2 inches of styrocrete,on grade, at about 1 cement 2 sand 6 or 8 ground up styrofoam by volume.
4 inches of tar covered styrofoam
piping and sand to just cover the pex heat pipe
2" normal cement possibly with mesh.
for a normal house hold floor.
My concern is with the tar, over the years it does not seem to have harmed the foam, but will the tar/oils be able to migrate upwards through the concrete?
Your thoughts would be appreciated.

nibs is offline   Reply With Quote
Old 05-06-16, 10:29 PM   #2
nibs
Apprentice EcoRenovator
 
Join Date: Jun 2010
Posts: 206
Thanks: 1
Thanked 18 Times in 17 Posts
Default

Note to add;
Have done quite a bit with "styro crete" at the mix above, with good results.
Have found that by putting down a couple of inches of wet styrocrete, then placing the foam with a back and forth motion the foam is very well supported I can walk on 2 inch thick styrofoam with no cracking once the styrocrete is 24 hrs cured.
nibs is offline   Reply With Quote
Old 05-08-16, 02:48 PM   #3
AC_Hacker
Supreme EcoRenovator
 
AC_Hacker's Avatar
 
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 723 Times in 534 Posts
Default

Quote:
Originally Posted by nibs View Post
...piping and sand to just cover the pex heat pipe...
Curious why you would want to cover the PEX with dry sand? Compared to concrete, dry sand is not such a good conductor of heat.

Look it up in the Engineers Handbook

-AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker...
AC_Hacker is offline   Reply With Quote
Old 05-09-16, 10:58 PM   #4
nibs
Apprentice EcoRenovator
 
Join Date: Jun 2010
Posts: 206
Thanks: 1
Thanked 18 Times in 17 Posts
Default

Thanks AC, had not thought of the heat transfer. Sand was suggested by a fellow from Alberta, where it gets really cold, his opinion was that the sand allowed some movement in the Pex as it heated and cooled, he had done a few churches that way. Seemed like a good idea & with 4" of foam under, I suspect the heat transfer losses would not be significant.
nibs is offline   Reply With Quote
The Following User Says Thank You to nibs For This Useful Post:
AC_Hacker (05-10-16)
Old 05-10-16, 08:31 AM   #5
AC_Hacker
Supreme EcoRenovator
 
AC_Hacker's Avatar
 
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 723 Times in 534 Posts
Default

Quote:
Originally Posted by nibs View Post
Thanks AC, had not thought of the heat transfer. Sand was suggested by a fellow from Alberta, where it gets really cold, his opinion was that the sand allowed some movement in the Pex as it heated and cooled, he had done a few churches that way. Seemed like a good idea & with 4" of foam under, I suspect the heat transfer losses would not be significant.
"Thanks AC, had not thought of the heat transfer."

You are about to spend a lot of money and time working on a project that is specifically about thermal transfer, that you will live with for many years, and you have not thought about thermal transfer?

There is a problem here.

It looks like you did not look at the information I gave you. So I will make it easy... look at this:

From this source:
What is thermal conductivity for sand
Thermal Conductivity (W/m K) of
>Coarse SAND (dry) is 0.25 (W/m K)
>Medium SAND (dry) is 0.27 (W/m K)
>Fine SAND (dry) is 0.15 (W/m K)


From this source:
http://www.orbee.org/images/5cc-reso...-materials.pdf
Thermal Conductivity of concrete = 1.28 (W/m K)

This means that on average, concrete is almost 6 times better than dry sand at conducting heat.

In the long run it means that if you use sand, you will be paying more money to heat your house, every year, as long as you live there.

It is your floor, it is your money, it is your project.

-AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker...
AC_Hacker is offline   Reply With Quote
Old 05-11-16, 12:00 AM   #6
nibs
Apprentice EcoRenovator
 
Join Date: Jun 2010
Posts: 206
Thanks: 1
Thanked 18 Times in 17 Posts
Default

Thanks again AC, my Marks is buried deep under construction materials right now.
It will be two years before we pour the floors, so have not bothered to do the math yet. The sand idea was put forth over a few beer on the beach in Mexico, so not to worry.
Am more concerned right now with the asphalt covered styrofoam, if we decide to use it, I need to get it soon, so was hoping for feedback on that.
Or ways to ensure the asphalt oils do not migrate (capillary action) upwards
nibs is offline   Reply With Quote
Old 08-11-16, 10:30 PM   #7
nibs
Apprentice EcoRenovator
 
Join Date: Jun 2010
Posts: 206
Thanks: 1
Thanked 18 Times in 17 Posts
Default

Boy no opinions on using the tar covered insulation below the slab on grade floor.
Still wondering if the oils from the tar might migrate upwards through the cement.
Or what material, plastic?, would control it. It sure is a lot of insulation for not much money.
nibs is offline   Reply With Quote
Old 08-12-16, 12:38 PM   #8
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,428
Thanks: 431
Thanked 619 Times in 517 Posts
Send a message via Yahoo to jeff5may
Default

Highly unlikely the tar will go anywhere unless it gets pretty hot, as in above boiling point of water. Over the centuries, it may extrude out the sides, but again highly unlikely within your lifetime...especially considering the compressibility of the styrofoam.

jeff5may is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:57 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design