EcoRenovator  

Go Back   EcoRenovator > Improvements > Lawn and Garden
Advanced Search
 


Blog Register 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 04-16-16, 10:45 PM   #1
Mukiwa
Lurking Renovator
 
Join Date: Sep 2015
Location: BC
Posts: 15
Thanks: 2
Thanked 0 Times in 0 Posts
Default Lawn mower battery leads

There is a break somewhere on the lead between by battery and starter on my John Deere mower. I've decided to replace the leads but I don't know what gauge wire they are as I want to order the cables+lugs online.

Mukiwa is offline   Reply With Quote
Old 04-17-16, 06:21 AM   #2
hamsterpower
Apprentice EcoRenovator
 
Join Date: Oct 2009
Posts: 142
Thanks: 0
Thanked 11 Times in 11 Posts
Default

Based on the info provided I will gaze into my crystal ball... I see guage 4 but the answer is a bit fuzzy.. it could be 2. Any pre-made cable of the correct length should be up to the task if it is a garden tractor.
hamsterpower is offline   Reply With Quote
Old 04-17-16, 09:28 AM   #3
jeff5may
Supreme EcoRenovator
 
Join Date: Jan 2010
Location: elizabethtown, ky, USA
Posts: 2,394
Thanks: 410
Thanked 604 Times in 506 Posts
Send a message via Yahoo to jeff5may
Default

Troubleshoot first. Could be a safety cutout, the key or pushbutton switch, or starter solenoid. Usually heavy gage wires fail at the ends unless the are mechanically severed somehow. Loose connections get hot and stop working.
jeff5may is offline   Reply With Quote
Old 04-17-16, 11:54 AM   #4
Mukiwa
Lurking Renovator
 
Join Date: Sep 2015
Location: BC
Posts: 15
Thanks: 2
Thanked 0 Times in 0 Posts
Default

I bought a ride on mower that needed a starter and the more I look into it it looks like they tipped it over and the battery ripped out (lugs pulled off cables & hood is broken off..) I hooked 12v up to the battery leads and here was no voltage at the starter terminal.. I hooked 12v up directly to the new starter and it turned over right away so I'm assuming the cables were damaged somewhere.. I'll be tearing it right apart when I have a free weekend.
Mukiwa is offline   Reply With Quote
Old 04-17-16, 02:38 PM   #5
stevehull
Steve Hull
 
Join Date: Dec 2012
Location: hilly, tree covered Arcadia, OK USA
Posts: 829
Thanks: 241
Thanked 165 Times in 123 Posts
Default

Mukiwa,

Save some money vs. buying this cable. Get some insulated AWG4 stranded copper wire ($1 per foot; Lowes, Home Depot). Then get the appropriate sized lugs to fit on the ends (auto supply store; maybe $2 ). Solder these on using (no acid flux) and away you go. I use a propane torch for this, but be careful so you don't melt too much insulation. I usually finish it off by wrapping some electrical tape where the insulation melted off a bit.

The leads normally on ride on mowers (between solenoid and starter bolt) are cheap and are not thick enough. This extra sized cable will also insure the battery stays charged,

Good luck.


Steve

__________________
consulting on geothermal heating/cooling & rational energy use since 1990
stevehull is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:41 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design