EcoRenovator  

Go Back   EcoRenovator > Improvements > Appliances & Gadgets
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 11-03-22, 09:13 PM   #11
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default Changed my mind about input air

Today, I didn't allow enough air into the basement while running the radon fan for 4 hours. 12:00 to 16:00
Ended up with more Radon! It was pulled out of the sump holes and cracks in the floor! I created a little vacuum and got punished. No Ham radio in the basement tonight!

The radon was low at noon. But I wanted to ventilate the basement to freshen up the air. I opened the pull-down stairs to the attic, thinking cool air would flow down. But it was so hot today in the attic, there was no down-flow of attic air. It was likely a suction effect. Especially if attic vent fan turned on (auto-on at 120F).

I'm going to need some way of bringing in outside air into the basement. When it's cold outside, that will be a real problem. I don't want a lot of cold air on the basement floor while the Radon fan is running.

~~~
On another note, I need to look at the Radon after the oil burner has been running! That thing sucks too!

Cheers,
Rich

Attached Thumbnails
Click image for larger version

Name:	radon.jpg
Views:	705
Size:	119.3 KB
ID:	9478  
__________________
My hobby is installing & trying to repair mini-splits
EPA 608 Type 1 Technician Certification ~ 5 lbs or less..
Xringer is offline   Reply With Quote
Old 11-03-22, 09:25 PM   #12
mincus
Helper EcoRenovator
 
Join Date: Feb 2009
Location: St. Louis, MO
Posts: 42
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I've seen a drastic improvement after sealing all cracks in the floor. The method of construction was to pour the basement walls, then later pour the floor. That left about a quarter-inch gap around the entire perimeter. I used a radon sealing caulk (from Menards) and sealed the entire perimeter. Since doing that, my levels are rarely above 2 or so. Usually in the 1 range. I think I'm almost nearing outdoor levels for most days.

Between the fan and the sealing, I've gone from almost 30 down to 1. Pretty awesome.

Just because I was curious, when we were out of town for 10 days, I turned the radon fan off. I anticipated not much increase, but boy was I wrong. Even with the sealing, it jumped to 17. Needless to say, keeping the fan on all the time now.
mincus is offline   Reply With Quote
Old 11-03-22, 09:52 PM   #13
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default The Right Stuff

It sounds like you're doing it right. My old basement could be sealed with a lot of work. So it's not gonna happen.

I looked at the afternoon 24 hour plot and saw a 4.6 peak at 17:30. The oil burner ran from 17:00 until 17:20. (We are trying to make this tank last until WW3 starts)
It's clearly sucking up some radon and shooting some up the chimney. I'll bet most of the houses on this granite hill do the same thing.
The good news is, two of the new families on my street have installed Mini-Splits during the last month.
The new kids next door went with Propane heat. They are already talking about moving to Florida (from MA).
I don't blame them.
Attached Thumbnails
Click image for larger version

Name:	peak.jpg
Views:	697
Size:	107.5 KB
ID:	9479  
__________________
My hobby is installing & trying to repair mini-splits
EPA 608 Type 1 Technician Certification ~ 5 lbs or less..
Xringer is offline   Reply With Quote
Old 11-04-22, 11:10 PM   #14
mincus
Helper EcoRenovator
 
Join Date: Feb 2009
Location: St. Louis, MO
Posts: 42
Thanks: 0
Thanked 0 Times in 0 Posts
Default

I've wondered about all those oil burners you have in that part of the world. Any affect on the air quality overall in the area?
mincus is offline   Reply With Quote
Old 11-05-22, 09:35 AM   #15
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default

Quote:
Originally Posted by mincus View Post
I've wondered about all those oil burners you have in that part of the world. Any affect on the air quality overall in the area?
Looking at the New Cases (of lung cancer) map, it seems okay in this area. Not too bad..
https://www.lung.org/getmedia/381ca4...0-report-final

Attached Thumbnails
Click image for larger version

Name:	map.jpg
Views:	678
Size:	214.3 KB
ID:	9480  
__________________
My hobby is installing & trying to repair mini-splits
EPA 608 Type 1 Technician Certification ~ 5 lbs or less..
Xringer is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:20 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design