EcoRenovator  

Go Back   EcoRenovator > Improvements > Biofuels
Advanced Search
 


Blog 60+ Home Energy Saving Tips Recent Posts Search Today's Posts Mark Forums Read


Reply
 
Thread Tools Display Modes
Old 11-26-10, 10:44 AM   #1
Daox
Administrator
 
Daox's Avatar
 
Join Date: Aug 2008
Location: Germantown, WI
Posts: 5,525
Thanks: 1,162
Thanked 374 Times in 305 Posts
Default Modifying a wood furnace to increase efficiency

My cousin just dropped me off a nice little wood furnace for my garage. Yep, another freebie! But, it does need work. From the name plate on it it looks like its from the early 80s. It is VERY simple which is great. However, it does not have a dedicated inlet for combustion chamber air. Its also pretty small so I'm guessing a lot of heat will escape out of the flue.

I am looking to refurbish this furnace as well as modify it to increase the efficiency. I am looking for ideas! It'll obviously need a dedicated intake for the combustion air. I'm not sure what can be done with the flue to increase efficiency so I'm looking for ideas there. I am also thinking of running some plumbing to it to work as an auxiliary water heater since I'm sure it'll provide more heat than is needed to heat my garage. Anyway, I don't know a lot about furnace design or anything so if anyone has any links to info or anything it would be great.

Here are the pictures:

Front of the furnace. The rust is not only from use, but sitting outside for a while.







Here you can see the problem with the unit. It has several holes in the back. I'll just weld them shut.



This is the back side. Again you can see the holes.



A nice perspective shot. The one hole under the exhaust flue is fairly good in size. Nothing that can't be fixed though.



Here is the unit without the cover over it. There is a blower that attaches under the unit and blows air over the combustion chamber and the hot air exits the top via a large duct. Pretty simple design.



Here is where the blower attaches on the bottom.



This is where the air comes up from the bottom and around the sides.

__________________
Current project -
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
&
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Last edited by Daox; 11-26-10 at 10:47 AM..
Daox is offline   Reply With Quote
Old 11-26-10, 04:39 PM   #2
MetroMPG
Infrequent noob
 
Join Date: Aug 2008
Location: 1000 Islands region, Ontario, Canada
Posts: 402
Thanks: 37
Thanked 20 Times in 19 Posts
Default

Woohoo! Someone's getting a heated garage

Very commercial/industrial looking.

I found out today I may also be on the receiving end of a "new to me" wood stove to replace the worn out old thing currently heating the workshop.
__________________
.

  • To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

  • To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

  • To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

  • To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
MetroMPG is offline   Reply With Quote
Old 11-26-10, 06:22 PM   #3
Ryland
Master EcoRenovator
 
Join Date: Mar 2009
Location: Western Wisconsin.
Posts: 913
Thanks: 127
Thanked 82 Times in 71 Posts
Default

I've done wood stove repairs before when they devolped cracks like that and the best thing I can suggest is to put a patch over and zig zag the welds or you will have the cracks reopen, lining the inside with fire brick is really the best idea, welding some angle iron in to hold the fire brick would be a good idea, this keeps the fire box hotter without deforming or burning the steel sides of the box, a hotter fire burns cleaner and burns the fuel more completely.
If you want to keep it simple, have your chimney as it exits the back drop down instead of going up, the downward loop extends down a 2-3 feet then goes up, to get a fire started you are going to need to install a "T" with a solid baffle so the smoke can go straight out and up, this will help extract a great of heat out of the smoke while still in the fire box by only letting the coolest of the smoke exit, more modern furnaces have the chimney opening at the bottom to create the same affect.

I am also a big fan of devices like the Magic Heat

I've seen a number of these devices in place and everyone seems really happy with them as they not only help move the warm air but they pull more heat out of the smoke and they have a baffle cleaner built in to keep it cleaning and working.
If you want to heat water a single loop of stainless pipe should work as a slow preheat otherwise wrapping a coil around the chimney that then goes through the fire box should heat up faster so you can heat a tank or floor faster.
Ryland is offline   Reply With Quote
The Following User Says Thank You to Ryland For This Useful Post:
Piwoslaw (11-27-10)
Old 11-26-10, 07:35 PM   #4
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default

If you plan to locate the stove near a wall (or walls in a corner), you might want to think
about using a reflective shield over any insulation or fire-proofing.

A reflector, will keep the radiant heat inside the garage. Without wasting fuel/heat on the
interior studs etc and exterior of nearby walls.
Xringer is offline   Reply With Quote
Old 11-27-10, 07:53 AM   #5
NeilBlanchard
Journeyman EcoRenovator
 
NeilBlanchard's Avatar
 
Join Date: Dec 2009
Location: Maynard, MA Eaarth
Posts: 383
Thanks: 78
Thanked 39 Times in 32 Posts
Default

16-18 gauge galvanized steel on about 3/4-1" standoffs makes a effective heat shield. We has this around a wood stove, and on the other side of the wall, you could easily find the edge of the shield by feeling the temperature difference. The shield should go several feet beyond the extents of the stove.
NeilBlanchard is offline   Reply With Quote
Old 11-27-10, 08:55 AM   #6
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default

The stand-offs / air space is very important to get good reflectance.

YouTube - Radiant Barrier Under Shingles Won't Work Without An Air Space
Xringer is offline   Reply With Quote
Old 11-27-10, 11:15 AM   #7
iamgeo
Apprentice EcoRenovator
 
Join Date: Aug 2010
Location: Lakehills, Tx
Posts: 168
Thanks: 4
Thanked 10 Times in 9 Posts
Default

Is that a goats leg in the lower right of the first pic?
iamgeo is offline   Reply With Quote
Old 11-27-10, 01:37 PM   #8
Xringer
Lex Parsimoniae
 
Xringer's Avatar
 
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
Default

Quote:
Originally Posted by iamgeo View Post
Is that a goats leg in the lower right of the first pic?
The goat with a pink collar in the 7th pic??
Xringer is offline   Reply With Quote
Old 11-27-10, 02:47 PM   #9
iamgeo
Apprentice EcoRenovator
 
Join Date: Aug 2010
Location: Lakehills, Tx
Posts: 168
Thanks: 4
Thanked 10 Times in 9 Posts
Default

Ha! I missed that one.
iamgeo is offline   Reply With Quote
Old 11-28-10, 12:33 PM   #10
Piwoslaw
Super Moderator
 
Piwoslaw's Avatar
 
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 111 Times in 87 Posts
Default

Never seen a goat in a collar, in a pink one?

Piwoslaw is offline   Reply With Quote
Reply


Tags
furnace, modify, stove, wood

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:35 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Ad Management by RedTyger
Inactive Reminders By Icora Web Design