![]() |
![]() |
#451 | |
Lurking Renovator
Join Date: Jul 2014
Location: UK
Posts: 4
Thanks: 4
Thanked 0 Times in 0 Posts
|
![]() Quote:
Alas these seem to be aimed at moderate sized houses or larger. The smallest I did find was a Dimplex SIH 4 ME (4KW) but it is listing at £3.5K/$6K. Several times more than a 5KW Diesel Water Heater designed for a Marine environment. The power use of the heat pump will need looking into carefully. Also I have a feeling from my initial reading it would take 1KW.hr as an input (EG in a 4KW Heat Pump that needs 1KW electrickery), whereas a 5KW Diesel Water Heater would need 35-50 W.hr as an input (for the circulation pump & control unit aspects... IE nearly nothing). Power is a big concern as previously mentioned. Still, DIY to the rescue? Do you have any more specific advice/pointers in this regard? Cheers! Last edited by Jim_UK; 07-28-14 at 08:36 PM.. |
|
![]() |
![]() |
![]() |
#452 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
You should find a good bit of information there. -AC_Hacker
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
The Following User Says Thank You to AC_Hacker For This Useful Post: | Jim_UK (07-28-14) |
![]() |
#453 | |
Supreme EcoRenovator
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
|
![]() Quote:
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her... |
|
![]() |
![]() |
![]() |
#454 | |
Lurking Renovator
Join Date: Jul 2014
Location: UK
Posts: 4
Thanks: 4
Thanked 0 Times in 0 Posts
|
![]() Quote:
Currently planned: There will be two 14KW PM DC motors for propulsion. 1KW Solar, 40KW Batteries & 5-8KW Diesel Generator (+ occasional 3.5KW Shoreline). It's an 'all' electric boat (well Diesel/Electric Serial Hybrid technically speaking due to generator - and the 5KW Diesel water heater previously mentioned). |
|
![]() |
![]() |
![]() |
#455 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
-AC
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
![]() |
#456 |
Supreme EcoRenovator
Join Date: Oct 2008
Location: Austin, TX
Posts: 1,154
Thanks: 14
Thanked 257 Times in 241 Posts
|
![]() Then it would be a range extender rather than an APU, but same idea.
Assuming the generator is 30% efficient (diesels generally do better) and the thermal recovery system can recover 80% of the waste heat, the heat pump only needs to get a COP of 1.47 (EER of 5) to beat an ideal furnace. For comparison, a cheap window A/C easily does 9.7 EER or more.
__________________
To my surprise, shortly after Naomi Wu gave me a bit of fame for making good use of solar power, Allie Moore got really jealous of her... |
![]() |
![]() |
![]() |
#457 |
Helper EcoRenovator
Join Date: Aug 2014
Location: The Netherlands
Posts: 70
Thanks: 18
Thanked 26 Times in 14 Posts
|
![]() Hello everyone,
I'm a relatively new ecorenovator. Concerning this site it is. I've been working on my house for a number of years now and probably considered a bit of a geek by many people, but it's nice to see I'm not the only one!! I've read the whole thread from AC-Hacker about building a heat pump, a little in the conservation section and this thread. It took me a few days... I have a house that's CO2-neutral (including the electric car BMW i3). The house was built in 1987 including a balanced ventilation system with heat recovery (1 cross flow hx). So it should be OK. But the efficiency I measured was approx 65%. This is only based on measured temperatures. So not including moisture effects. So in reality it could be a bit off the real value. I thought about improving (or replacing) my system to achieve a better efficiency. However I'm also concerned about the AC-fans I have. To my opinion DC fans must be much more efficient, especially because in normal conditions (medium flow) my AC-fans run with a high "slip" (percentage of difference between the rotational speed of the fan and of the rotational speed of the electrical/magnetical field). This is achieved by a series capacitor. But thinking about my centrifugal fans, I wondered about the fact that in this thread I almost all the times am reading about small axial fans. In my opinion generally the combination of hx, filters, ducting etc. requires a dp that most axial fans don't produce. Of course I've seen the efficiency calculations (based on temperatures) in this thread and they sometimes looked impressive! But I wonder if someone really did flow measurements. I fear that in many installations the efficiency might be OK, but the flow is just far below what's required. Normally in Europe we calculate these installations with 30m3/hr per person and some minimum values for toilet and bathroom. Just curious about the measured flows. Anyone? If you want to see details about our house and how we achieved CO2-neutrality, take a look at our site. It's in Dutch, but Google translate can help (although sometimes the translations are funny/odd). The title means: No more energy bill. Here it is: geen energierekening meer: energieneutraal woonhuis fam. Kriegsman Ootmarsum - Rekening energiebedrijf 2013 |
![]() |
![]() |
![]() |
#458 | ||
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
You have achieved a goal that most of us haven't even allowed ourselves to dream of... and you have done it, very nice. Quote:
Good point! I did some experimental work that was posted on the DIY HRV thread, and Mike, the guy I was working with, happened to have a precision air volumetric measuring meter. They're really expensive and he was pretty lucky to have found one used, in good condition, and cheap. In the DIY HRV thread also, there is a procedure described that uses very large plastic bags, and their volume is estimated and the time-to-fill is measured. I know it sounds very crude, but it should give you a good approximation of air volume rate. -AC
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
||
![]() |
![]() |
![]() |
#459 | |
Helper EcoRenovator
Join Date: Aug 2014
Location: The Netherlands
Posts: 70
Thanks: 18
Thanked 26 Times in 14 Posts
|
![]() Quote:
Otherwise you could only measure the hx + filters. On the other hand... that's better than no measurements at all. I had the opportunity to borrow a flow-measuring device that's intended to measure airflows from ventilationsystems (TSI Velocicheck including air capture hood). In this way I was able to measure each separate supply nozzle and extraction nozzle and after that, I could adjust the nozzles so that incoming and outgoing air were really balanced. |
|
![]() |
![]() |
![]() |
#460 | |
Supreme EcoRenovator
Join Date: Mar 2009
Location: Portland, OR
Posts: 4,004
Thanks: 303
Thanked 724 Times in 534 Posts
|
![]() Quote:
The bag method takes care of those differences. But if you only want to balance velocities, I suppose a center measure would do it. -AC
__________________
I'm not an HVAC technician. In fact, I'm barely even a hacker... |
|
![]() |
![]() |
![]() |
Tags |
erv, heat recovery, hrv |
|
|