I ordered a 4x4 CNC plasma table - Page 4

pinballlooking · 01-07-20, 02:27 PM

The most it will be lifting is ½” plate about 653 pounds.
My tractor just lifted 3/8” plate about 500 pounds.

I checked my hydraulic pressure and mine was low on my tractor I bumped it up and it was able the lift the 3/8 plate.

pinballlooking · 01-07-20, 03:09 PM

Here is the first part I cut out the 3/8” but I used a new cam software so I could start the cut from the center of the 30MM Circle (lead in).

But it made my 30mm holes cut 28mm the kerf width is not right. That is what the torch cuts out like a blade width. Once I have that adjusted, they will be back to 30mm.

WyrTwister · 01-08-20, 03:45 AM

Looks very smooth & precise . :-)

Best of luck .

Wyr
God bless

pinballlooking · 01-27-20, 01:27 PM

About a year ago I made a quick connect for my backhoe. I have use it on many projects and it works well. At that time, I was cutting everything with a Porta band saw.

Now I have a 4x8 CNC plasma table a mag drill… I am making a new QC for my backhoe. I plan on selling these Quick connects. I almost have it ready.

I have the Jig for welding the sides up done. This is made out of 3/8" plate steel.
I am using the plasma marking feature to mark where to drill and weld the sides.

It is very close to being ready to reproduce. It will not be a high-volume item. You have to have a CB65 backhoe and more than one attachment.
I think next up will be a root ripper. A reason for getting my QC.

This allows you to change out backhoe attachments in usually under 60 seconds.

pinballlooking · 01-29-20, 12:10 AM

I changed my band-saw from 3 phase over to 120 volts. I ordered an over current and motor controller all in one. New 1HP 120 Volt motor.
I put all new blade bearings and bearing bushings on it. New blade new belt new belt and blade cleaner brushes

On the old controller cover I used my plasma table to cut out a place for the switch.
Tomorrow I will adjust the blade.

I worked on the bandsaw again tonight.
I added a shunt to the motor controller. This is an item that snaps to the side of the motor controlled. When it gets energize it turns off the switch.

The motor controller feeds power to the shunt then there is a switch that closes when the saw finishing cutting. So this is a self-collapsing cricket.

The saw completes the cut and I shuts its off. Them you must turn the motor controller back on to start cutting again. (It worked similar to this from the factory but I totally gutted and reworked it for 120 volts.)

I had to change the motor wiring to make it run CW and flip the blade inside out to make the rake got the right direction.
It is cutting good right now. I still need to do a few things but I can use it now.

pinballlooking · 02-03-20, 04:36 PM

My first product is out.
Here it is in action.

https://www.youtube.com/watch?v=o5k1x9FJw5o

Daox · 02-03-20, 05:29 PM

Looks pretty nice! Hope you sell many!

pinballlooking · 02-13-20, 11:26 AM

I now have a root ripper for sale. I call it the Hammerhead.
This one is made with 1/2” steel plate.

4' x 8' 1/2" plate was 654 pounds.
My tractor could just handle this.

I am trying to get my powder coating setup. I sold my first quick connect and root ripper they will ship next week.

pinballlooking · 02-20-20, 11:55 AM

I finally put some castors on Band saw because it very heavy to move.
(Almost 1K pounds )

Glad to get it done.

pinballlooking · 06-16-20, 12:03 AM

My CNC plasma table is paid for with profit. Over ½ of all the equipment I bought is paid for with profit.
Hopefully the rest will be paid for this summer.

My oldest son is working with me on making products.
He is going to use the money for college.
He is running CNC plasma table dimpling steps bending them in press brake.
Sand blasting and powder coating them.
All good skills.

01-07-20, 02:27 PM	#31
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	The most it will be lifting is ½” plate about 653 pounds. My tractor just lifted 3/8” plate about 500 pounds. I checked my hydraulic pressure and mine was low on my tractor I bumped it up and it was able the lift the 3/8 plate. __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Last edited by pinballlooking; 01-07-20 at 09:57 PM..

01-07-20, 03:09 PM	#32
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	Here is the first part I cut out the 3/8” but I used a new cam software so I could start the cut from the center of the 30MM Circle (lead in). But it made my 30mm holes cut 28mm the kerf width is not right. That is what the torch cuts out like a blade width. Once I have that adjusted, they will be back to 30mm. Attached Thumbnails __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

01-27-20, 01:27 PM	#34
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	About a year ago I made a quick connect for my backhoe. I have use it on many projects and it works well. At that time, I was cutting everything with a Porta band saw. Now I have a 4x8 CNC plasma table a mag drill… I am making a new QC for my backhoe. I plan on selling these Quick connects. I almost have it ready. I have the Jig for welding the sides up done. This is made out of 3/8" plate steel. I am using the plasma marking feature to mark where to drill and weld the sides. It is very close to being ready to reproduce. It will not be a high-volume item. You have to have a CB65 backhoe and more than one attachment. I think next up will be a root ripper. A reason for getting my QC. This allows you to change out backhoe attachments in usually under 60 seconds. Attached Thumbnails __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

01-29-20, 12:10 AM	#35
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	I changed my band-saw from 3 phase over to 120 volts. I ordered an over current and motor controller all in one. New 1HP 120 Volt motor. I put all new blade bearings and bearing bushings on it. New blade new belt new belt and blade cleaner brushes On the old controller cover I used my plasma table to cut out a place for the switch. Tomorrow I will adjust the blade. I worked on the bandsaw again tonight. I added a shunt to the motor controller. This is an item that snaps to the side of the motor controlled. When it gets energize it turns off the switch. The motor controller feeds power to the shunt then there is a switch that closes when the saw finishing cutting. So this is a self-collapsing cricket. The saw completes the cut and I shuts its off. Them you must turn the motor controller back on to start cutting again. (It worked similar to this from the factory but I totally gutted and reworked it for 120 volts.) I had to change the motor wiring to make it run CW and flip the blade inside out to make the rake got the right direction. It is cutting good right now. I still need to do a few things but I can use it now. Attached Thumbnails __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Last edited by pinballlooking; 01-29-20 at 10:42 PM..

02-03-20, 05:29 PM	#37
Daox Administrator Join Date: Aug 2008 Location: Germantown, WI Posts: 5,525 Thanks: 1,162 Thanked 374 Times in 305 Posts	Looks pretty nice! Hope you sell many! __________________ Current project - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. & To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

01-08-20, 03:45 AM	#33
WyrTwister Master EcoRenovator Join Date: Jun 2013 Location: USA Posts: 543 Thanks: 6 Thanked 44 Times in 38 Posts	Looks very smooth & precise . :-) Best of luck . Wyr God bless

02-13-20, 11:26 AM	#38
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	I now have a root ripper for sale. I call it the Hammerhead. This one is made with 1/2” steel plate. 4' x 8' 1/2" plate was 654 pounds. My tractor could just handle this. I am trying to get my powder coating setup. I sold my first quick connect and root ripper they will ship next week. Attached Thumbnails __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Last edited by pinballlooking; 02-21-20 at 12:41 PM..

02-20-20, 11:55 AM	#39
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	I finally put some castors on Band saw because it very heavy to move. (Almost 1K pounds ) Glad to get it done. Attached Thumbnails __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

06-16-20, 12:03 AM	#40
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,923 Thanks: 172 Thanked 564 Times in 463 Posts	My CNC plasma table is paid for with profit. Over ½ of all the equipment I bought is paid for with profit. Hopefully the rest will be paid for this summer. My oldest son is working with me on making products. He is going to use the money for college. He is running CNC plasma table dimpling steps bending them in press brake. Sand blasting and powder coating them. All good skills. __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.