![]() |
![]() |
#1 |
Apprentice EcoRenovator
Join Date: Oct 2010
Posts: 105
Thanks: 0
Thanked 10 Times in 8 Posts
|
![]() i have read most of the heat pump manifesto and joined the site because of it
i am the installer for a solar pv and thermal company. my soil temp is 70* from 2' to 6' didnot go farther my plan was to retrofit my existing ac system with a refrigerant to water heat exchanger on the condenser side like this one www .aquasystemsinc. com/models_test.html Aqua Systems efficient Liquid to Refrigerant Heat Exchangers there only $140 for the 2 ton unit. the owner is very helpfull and has some geo thermal experience and connect a slinky loop field to the exchanger and cool the condenser but now i plan on using a FHP 24,000btu geothermal heatpump (Florida Heat Pump) my house is 1000 sq ft and i have a 2 ton ac unit and resistance heating i have plenty of space for a slinky coil trench and maybe free access to a backhoe. my plan is to dig down 6' where the soil is very moist and lay my slinky. the heat exchanger guy gave me a figure of 100' of trench per ton with 400' of pipe in the 100' trench i have also heard that 600 foot of pipe slinky will fit in 65' of trench im guessing tighter spacing. i was thinking of diging 3 trenches around 80' long 3' wide and 6' deep and putting in around 750' of pipe in each trench. i located 800' roles of hdpe 3/4'' pipe which would leave me 25' extra on each input and output to reach my heat exchanger with no welds at all any helpfull insite i think i have it figured out it seems simple do you think i should see a large efficiency increase based on my soil temp of 70* thanks joe sebring fl 33876 Last edited by rhino 660; 02-16-12 at 09:23 PM.. |
![]() |
![]() |
![]() |
#2 | |
Super Moderator
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 110 Times in 86 Posts
|
![]() Quote:
That temperature may also be low enough to dehumidify the air.
__________________
Ecorenovation - the bottomless piggy bank that tries to tame the energy hog. |
|
![]() |
![]() |
![]() |
#3 |
Apprentice EcoRenovator
Join Date: Oct 2010
Posts: 105
Thanks: 0
Thanked 10 Times in 8 Posts
|
![]() i thought that even with the 70* ground loop temp i could only get the house to 78* or so
72* would be perfect but seems to good to be true |
![]() |
![]() |
![]() |
#4 |
Journeyman EcoRenovator
Join Date: May 2009
Location: Buffalo, NY
Posts: 344
Thanks: 3
Thanked 17 Times in 15 Posts
|
![]() That depends on the performance of your heat exchanger, and how quickly you need to remove heat from the house to hold that temperature.
|
![]() |
![]() |
![]() |
#5 |
Super Moderator
Join Date: May 2009
Location: Warsaw, Poland
Posts: 964
Thanks: 189
Thanked 110 Times in 86 Posts
|
![]() Yeah, either good thermal insulation of the house, or a good HX with a ground loop that can quickly take in the heat, would work. Of course, insulation is the better option.
I wonder if it would be possible to get rid of the ground loop's heat at night, say some outdoor HX?
__________________
Ecorenovation - the bottomless piggy bank that tries to tame the energy hog. |
![]() |
![]() |
![]() |
#6 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
|
![]() I wish that I had some 70F ground. My basement floor is holding at just under 50F these days...
![]() If you had some surface freeze protection, you wouldn't even need a water-glycol mix. Anyways, I wonder if you have any ground water in the area? Otherwise some of that heat you are pumping into the ground might built up after a while. |
![]() |
![]() |
![]() |
#7 | |
Apprentice EcoRenovator
Join Date: Oct 2010
Posts: 105
Thanks: 0
Thanked 10 Times in 8 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#8 | |
Apprentice EcoRenovator
Join Date: Oct 2010
Posts: 105
Thanks: 0
Thanked 10 Times in 8 Posts
|
![]() Quote:
the guy i spoke to with the heat exchanger said that for my application wet ground is the best because the heat tries to drive the moisture away from the loop feild my concerns really are with adapting my existing a/c unit any thoughts thanks for the replies |
|
![]() |
![]() |
![]() |
#9 |
Lex Parsimoniae
Join Date: Feb 2009
Location: Woburn, MA
Posts: 4,918
Thanks: 114
Thanked 250 Times in 230 Posts
|
![]() Those heat exchangers have 2 inputs and outputs for the water.
That seems like some extra plumbing is going to be required. What is your 'existing ac system'? What will be required to adapt it to connect to the new exchanger? |
![]() |
![]() |
![]() |
#10 | |
Apprentice EcoRenovator
Join Date: Oct 2010
Posts: 105
Thanks: 0
Thanked 10 Times in 8 Posts
|
![]() Quote:
my a/c system is 24,000 btu's with an outdoor and indoor air exchangers hookup as far as i know will involve removing outdoor exchanger and brazing in the new water exchanger |
|
![]() |
![]() |
![]() |
|
|