I ordered a 4x4 CNC plasma table

pinballlooking · 07-08-19, 11:51 AM

I did a fair amount of research looking at build /buy a CNC table. I was close to making one but in the end buying just made more since.
I would have had more money in building one.
I have a lot to learn just in software to use it. It will be about 8 weeks before I get it. They build to order and they just had a sale.

I am getting a water table to keep smoke down and warping to a Min. It has torch height control.
I will be using my new plasma cutter on it. I will have to buy a CNC port board and a machine torch.

Delusional Designs
https://www.delusionaldesignscnc.com...ter_Table.html

I am not sure where our focus will be yet. I will be selling some stuff I cut but I would like to keep the finish and painting part to not much as this is a side business.
I am probably limited to ½” and under cuts. I will add an extension to the table to all put a 4’x8’ sheet on the table. If we like doing this we will buy a table extension to expand this table to 4’x8’ table.

https://www.youtube.com/watch?v=5OVGm56B_w0

Daox · 08-07-19, 10:23 AM

Have you used it yet?

pinballlooking · 08-07-19, 05:02 PM

I actually canceled this one and I am going to order the next model up from this one that uses linear rails better software. It will let you continue from the spot you had a issue. I am going to get the 4 x 8 table as this one is harder to upgrade later. I was able to get a machine torch off Ebay that had been only used once for a killer price. That will help with some costs. But I have to buy a bigger ticket compressor.

Daox · 08-07-19, 05:35 PM

Sounds fun. Do you have lifting equipment? A 4x8 sheet of metal can weigh a lot.

dremd · 08-07-19, 05:46 PM

Sweet dude!
I have a 4x14 plasma cam setup with a Hypertherm Powermax 45 on it.
What cutter are you planning on running?

If there’s anything you think I might know feel free to hit me up, but as I’m sure you already know Jim Colt is THE authority on small CBC plasma setups.

dremd · 08-07-19, 05:49 PM

I see you are interested in a water table, unless where you are venting to is smoke critical I wouldn’t. I had a water tank in mine and ended up pulling it out because it was a pain to clean and only helped so much.

pinballlooking · 08-07-19, 06:19 PM

Quote:

Originally Posted by dremd

Sweet dude!
I have a 4x14 plasma cam setup with a Hypertherm Powermax 45 on it.
What cutter are you planning on running?

If there’s anything you think I might know feel free to hit me up, but as I’m sure you already know Jim Colt is THE authority on small CBC plasma setups.

What do you mostly cut with yours?

dremd · 08-07-19, 06:30 PM

Originally I cut 20, 16, and 12 ga steel.
Now it spends its days cutting.040 ,080, .125 aluminum mainly in 5052

Typically daily cut time is only around 2 hours with run time closer to 2.5 hours. Typically 5 days a week, but that varies by season.

pinballlooking · 08-07-19, 07:55 PM

Quote:

Originally Posted by dremd

Originally I cut 20, 16, and 12 ga steel.
Now it spends its days cutting.040 ,080, .125 aluminum mainly in 5052

Typically daily cut time is only around 2 hours with run time closer to 2.5 hours. Typically 5 days a week, but that varies by season.

Do you cut parts? Maybe art stuff?

pinballlooking · 08-07-19, 06:15 PM

Quote:

Originally Posted by Daox

Sounds fun. Do you have lifting equipment? A 4x8 sheet of metal can weigh a lot.

My subcompact tractor has quick attach pallet forks. It can lift the steel. I also have a hydraulic lift table that I move pinball machines around with that can lift 1,000 pounds.

08-07-19, 10:23 AM	#2
Daox Administrator Join Date: Aug 2008 Location: Germantown, WI Posts: 5,525 Thanks: 1,162 Thanked 374 Times in 305 Posts	Have you used it yet? __________________ Current project - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. & To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

08-07-19, 05:02 PM	#3
pinballlooking Super Moderator Join Date: Jun 2013 Location: SC Posts: 2,930 Thanks: 172 Thanked 564 Times in 463 Posts	I actually canceled this one and I am going to order the next model up from this one that uses linear rails better software. It will let you continue from the spot you had a issue. I am going to get the 4 x 8 table as this one is harder to upgrade later. I was able to get a machine torch off Ebay that had been only used once for a killer price. That will help with some costs. But I have to buy a bigger ticket compressor. __________________ Current project Aquaponics system , Passive Solar Greenhouse build To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Solar Install 12.5 Kwh- To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Mini Split installs - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. EV Chevy Volt - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

08-07-19, 05:35 PM	#4
Daox Administrator Join Date: Aug 2008 Location: Germantown, WI Posts: 5,525 Thanks: 1,162 Thanked 374 Times in 305 Posts	Sounds fun. Do you have lifting equipment? A 4x8 sheet of metal can weigh a lot. __________________ Current project - To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. & To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

08-07-19, 05:46 PM	#5
dremd Need More Eco Join Date: Sep 2008 Location: Scott, La Posts: 172 Thanks: 2 Thanked 6 Times in 6 Posts	Sweet dude! I have a 4x14 plasma cam setup with a Hypertherm Powermax 45 on it. What cutter are you planning on running? If there’s anything you think I might know feel free to hit me up, but as I’m sure you already know Jim Colt is THE authority on small CBC plasma setups.

08-07-19, 05:49 PM	#6
dremd Need More Eco Join Date: Sep 2008 Location: Scott, La Posts: 172 Thanks: 2 Thanked 6 Times in 6 Posts	I see you are interested in a water table, unless where you are venting to is smoke critical I wouldn’t. I had a water tank in mine and ended up pulling it out because it was a pain to clean and only helped so much.

08-07-19, 06:30 PM	#8
dremd Need More Eco Join Date: Sep 2008 Location: Scott, La Posts: 172 Thanks: 2 Thanked 6 Times in 6 Posts	Originally I cut 20, 16, and 12 ga steel. Now it spends its days cutting.040 ,080, .125 aluminum mainly in 5052 Typically daily cut time is only around 2 hours with run time closer to 2.5 hours. Typically 5 days a week, but that varies by season.