EcoRenovator - View Single Post

takyka · 07-10-14, 12:30 PM

The settings menu looks like here below. The commands I type is in red, the responses are black, comments are blue

? help
"c <password>" enter config mode.
"c <anything>" leave config mode
"l 1w" list 1W devices
"l input" list input states
"l output" list output states
"l settings" list operating settings
"l net" list networking settings
"l on" Display log messages
"l off" Stop display log messages
"a <bus nr.> <1W nr.> <function nr.>" assign 1W device to function
"d <function nr.>" unlink 1w device from function
"n <IP setting nr.>" <setting> set IP parameters
"s <setting nr.> <value>" set parameters
"r udn" reset UDN2987 output driver
"reset!" do a sowtware reset

l 1w
List of 1W devices:
Bus:0 1W bus number
00;28B0BFA704000088 20.44C 0; (0) Air in device number, serial, measuret temperature (if device support it) assigned function number, assigned function description
01;28328EA704000045 20.81C 2; (0) Air evap. gas
02;286AC6A70400001D 20.13C 7; (0) Condenser gas
03;282EC6A7040000B4 20.44C unassigned device
04;28AED4A7040000A1 20.75C
05;28055CA80400006A 20.81C 1; (0) Air out
06;284382A7040000CB 20.06C 13; (0) Suction temp
07;2857FEA704000000 19.25C 8; (0) Condenser liquid
08;285F8DA704000082 20.06C
09;28FFBDA70400005A 19.31C 9; (0) Heating water in
Bus:1 no device on bus
Bus:2
00;281239BB030000BD 24.63C 11; (2) Electric box
Functions:
00; * Air in * means device assigned to function
01; * Air out
02; * Air evap. gas
03; Water evap. liquid
04; Water evap. gas
05; Well water in
06; Well water out
07; * Condenser gas
08; * Condenser liquid
09; * Heating water in
10; Heating Water out
11; * Electric box
12; Compressor
13; * Suction temp
14; Discharge temp
a 0 3 10 assign command, bus number, device number, function number see above
a 0 4 06 like above
l1w list new 1w config

List of 1W devices:
Bus:0
00;28B0BFA704000088 20.44C 0; (0) Air in
01;28328EA704000045 20.81C 2; (0) Air evap. gas
02;286AC6A70400001D 20.13C 7; (0) Condenser gas
03;282EC6A7040000B4 20.38C 10; (0) Heating Water out this...
04;28AED4A7040000A1 20.75C 6; (0) Well water out and this added
05;28055CA80400006A 20.75C 1; (0) Air out
06;284382A7040000CB 20.06C 13; (0) Suction temp
07;2857FEA704000000 19.25C 8; (0) Condenser liquid
08;285F8DA704000082 20.06C
09;28FFBDA70400005A 19.31C 9; (0) Heating water in
Bus:1
Bus:2
00;281239BB030000BD 24.69C 11; (2) Electric box
Functions:
00; * Air in
01; * Air out
02; * Air evap. gas
03; Water evap. liquid
04; Water evap. gas
05; Well water in
06; * Well water out
07; * Condenser gas
08; * Condenser liquid
09; * Heating water in
10; * Heating Water out
11; * Electric box
12; Compressor
13; * Suction temp
14; Discharge temp
li list inputs
List inputs:
Energy: 0
Heating: 0
DHV: 0
Cooling: 0
EEV Error: 0
Well flow: 0
Heat flow: 1
Condenser pressure A/D: 274 raw AD value
Evaporator pressure1 A/D: 151
Evaporator pressure2 A/D: 587
4-20mA A/D: 0
UDN2987 driver fault: 0
lo list outputs
List outputs:
Well pump pwm: 0
Well pump run: 0
Battery on: 0
Heating circulation pump: 0
Compressor: 0
Air evaporator fan: 0
EEV: 0
OUT7: 0
OUT8: 1
UDN2987 driver enable: 1
lsettings
Operating settings:
0; Maximum compressor restart rate (1/hour): 6
1; Compressor Start delay (s): 100
2; Error recovery delay (s): 300
3; Battery switch off delay (s): 300
4; Post heating circulation duration (s): 30
5; Pre heating circulation duration (s): 5
6; EEV error ignore time (s): 40
7; Well water flowrate heating(L/h): 500
8; Well water flowrate cooling(L/h): 300
9; Minimum well flowrate (L/h): 200
10; Minimum heating water flowrate (L/h): 300
11; Minimum well water discharge temperature (C): 4.0
12; Maximum condenser pressure (Bar): 24.0
13; Minimum superheat temperature (C): -4.0
14; Maximum superheat temperature (C): 30.0
15; Maximum compressor temperature (C): 100.0
16; Maximum starting pressure difference (Bar) 2.0
error: 13 this is the status word value errors are bitmapped

lnet
Networking settings:
00;IP address: 192.168.1.3
01;netmask: 255.255.255.0
02;gateway: 192.168.1.1
03;DNS server: 8.8.8.8
04;log server IP address: 192.168.1.1
05;UI port (UDP): 124
06;WEB port (TCP): 80
07;log server port: 2080
09;
reset!

?
"c <password>" enter config mode.
"c <anything>" leave config mode
"l 1w" list 1W devices
"l input" list input states
"l output" list output states
"l settings" list operating settings
"l net" list networking settings
"l on" Display log messages
"l off" Stop display log messages
"a <bus nr.> <1W nr.> <function nr.>" assign 1W device to function
"d <function nr.>" unlink 1w device from function
"n <IP setting nr.>" <setting> set IP parameters
"s <setting nr.> <value>" set parameters
"r udn" reset UDN2987 output driver
"reset!" do a sowtware reset
lon
Display log messages enabled. if event occures (error, command etc.)it is logged to screen with timestamp
loff
Display log messages disabled.

ls
Operating settings:
0; Maximum compressor restart rate (1/hour): 6
1; Compressor Start delay (s): 100
2; Error recovery delay (s): 300
3; Battery switch off delay (s): 300
4; Post heating circulation duration (s): 30
5; Pre heating circulation duration (s): 5
6; EEV error ignore time (s): 40
7; Well water flowrate heating(L/h): 500
8; Well water flowrate cooling(L/h): 300
9; Minimum well flowrate (L/h): 200
10; Minimum heating water flowrate (L/h): 300
11; Minimum well water discharge temperature (C): 4.0
12; Maximum condenser pressure (Bar): 24.0
13; Minimum superheat temperature (C): -4.0
14; Maximum superheat temperature (C): 30.0
15; Maximum compressor temperature (C): 100.0
16; Maximum starting pressure difference (Bar) 2.0
error: 13

s0 10 set option 0 to 10 (see above)
Not in config mode! upsss, settings are password protected
Prior to modify any settings please use "c <password>" to enter config mode.
c 2135 the magic code
Config mode ON
s0 10 let's try again
ls
Operating settings:
0; Maximum compressor restart rate (1/hour): 10
1; Compressor Start delay (s): 100
2; Error recovery delay (s): 300
3; Battery switch off delay (s): 300
4; Post heating circulation duration (s): 30
5; Pre heating circulation duration (s): 5
6; EEV error ignore time (s): 40
7; Well water flowrate heating(L/h): 500
8; Well water flowrate cooling(L/h): 300
9; Minimum well flowrate (L/h): 200
10; Minimum heating water flowrate (L/h): 300
11; Minimum well water discharge temperature (C): 4.0
12; Maximum condenser pressure (Bar): 24.0
13; Minimum superheat temperature (C): -4.0
14; Maximum superheat temperature (C): 30.0
15; Maximum compressor temperature (C): 100.0
16; Maximum starting pressure difference (Bar) 2.0
error: 13

That's it.

07-10-14, 12:30 PM	#5
takyka Helper EcoRenovator Join Date: Jul 2014 Location: Hungary Posts: 34 Thanks: 0 Thanked 16 Times in 10 Posts	menu and settings The settings menu looks like here below. The commands I type is in red, the responses are black, comments are blue ? help "c <password>" enter config mode. "c <anything>" leave config mode "l 1w" list 1W devices "l input" list input states "l output" list output states "l settings" list operating settings "l net" list networking settings "l on" Display log messages "l off" Stop display log messages "a <bus nr.> <1W nr.> <function nr.>" assign 1W device to function "d <function nr.>" unlink 1w device from function "n <IP setting nr.>" <setting> set IP parameters "s <setting nr.> <value>" set parameters "r udn" reset UDN2987 output driver "reset!" do a sowtware reset l 1w List of 1W devices: Bus:0 1W bus number 00;28B0BFA704000088 20.44C 0; (0) Air in device number, serial, measuret temperature (if device support it) assigned function number, assigned function description 01;28328EA704000045 20.81C 2; (0) Air evap. gas 02;286AC6A70400001D 20.13C 7; (0) Condenser gas 03;282EC6A7040000B4 20.44C unassigned device 04;28AED4A7040000A1 20.75C 05;28055CA80400006A 20.81C 1; (0) Air out 06;284382A7040000CB 20.06C 13; (0) Suction temp 07;2857FEA704000000 19.25C 8; (0) Condenser liquid 08;285F8DA704000082 20.06C 09;28FFBDA70400005A 19.31C 9; (0) Heating water in Bus:1 no device on bus Bus:2 00;281239BB030000BD 24.63C 11; (2) Electric box Functions: 00; * Air in * means device assigned to function 01; * Air out 02; * Air evap. gas 03; Water evap. liquid 04; Water evap. gas 05; Well water in 06; Well water out 07; * Condenser gas 08; * Condenser liquid 09; * Heating water in 10; Heating Water out 11; * Electric box 12; Compressor 13; * Suction temp 14; Discharge temp a 0 3 10 assign command, bus number, device number, function number see above a 0 4 06 like above l1w list new 1w config List of 1W devices: Bus:0 00;28B0BFA704000088 20.44C 0; (0) Air in 01;28328EA704000045 20.81C 2; (0) Air evap. gas 02;286AC6A70400001D 20.13C 7; (0) Condenser gas 03;282EC6A7040000B4 20.38C 10; (0) Heating Water out this... 04;28AED4A7040000A1 20.75C 6; (0) Well water out and this added 05;28055CA80400006A 20.75C 1; (0) Air out 06;284382A7040000CB 20.06C 13; (0) Suction temp 07;2857FEA704000000 19.25C 8; (0) Condenser liquid 08;285F8DA704000082 20.06C 09;28FFBDA70400005A 19.31C 9; (0) Heating water in Bus:1 Bus:2 00;281239BB030000BD 24.69C 11; (2) Electric box Functions: 00; * Air in 01; * Air out 02; * Air evap. gas 03; Water evap. liquid 04; Water evap. gas 05; Well water in 06; * Well water out 07; * Condenser gas 08; * Condenser liquid 09; * Heating water in 10; * Heating Water out 11; * Electric box 12; Compressor 13; * Suction temp 14; Discharge temp li list inputs List inputs: Energy: 0 Heating: 0 DHV: 0 Cooling: 0 EEV Error: 0 Well flow: 0 Heat flow: 1 Condenser pressure A/D: 274 raw AD value Evaporator pressure1 A/D: 151 Evaporator pressure2 A/D: 587 4-20mA A/D: 0 UDN2987 driver fault: 0 lo list outputs List outputs: Well pump pwm: 0 Well pump run: 0 Battery on: 0 Heating circulation pump: 0 Compressor: 0 Air evaporator fan: 0 EEV: 0 OUT7: 0 OUT8: 1 UDN2987 driver enable: 1 lsettings Operating settings: 0; Maximum compressor restart rate (1/hour): 6 1; Compressor Start delay (s): 100 2; Error recovery delay (s): 300 3; Battery switch off delay (s): 300 4; Post heating circulation duration (s): 30 5; Pre heating circulation duration (s): 5 6; EEV error ignore time (s): 40 7; Well water flowrate heating(L/h): 500 8; Well water flowrate cooling(L/h): 300 9; Minimum well flowrate (L/h): 200 10; Minimum heating water flowrate (L/h): 300 11; Minimum well water discharge temperature (C): 4.0 12; Maximum condenser pressure (Bar): 24.0 13; Minimum superheat temperature (C): -4.0 14; Maximum superheat temperature (C): 30.0 15; Maximum compressor temperature (C): 100.0 16; Maximum starting pressure difference (Bar) 2.0 error: 13 this is the status word value errors are bitmapped lnet Networking settings: 00;IP address: 192.168.1.3 01;netmask: 255.255.255.0 02;gateway: 192.168.1.1 03;DNS server: 8.8.8.8 04;log server IP address: 192.168.1.1 05;UI port (UDP): 124 06;WEB port (TCP): 80 07;log server port: 2080 09; reset! ? "c <password>" enter config mode. "c <anything>" leave config mode "l 1w" list 1W devices "l input" list input states "l output" list output states "l settings" list operating settings "l net" list networking settings "l on" Display log messages "l off" Stop display log messages "a <bus nr.> <1W nr.> <function nr.>" assign 1W device to function "d <function nr.>" unlink 1w device from function "n <IP setting nr.>" <setting> set IP parameters "s <setting nr.> <value>" set parameters "r udn" reset UDN2987 output driver "reset!" do a sowtware reset lon Display log messages enabled. if event occures (error, command etc.)it is logged to screen with timestamp loff Display log messages disabled. ls Operating settings: 0; Maximum compressor restart rate (1/hour): 6 1; Compressor Start delay (s): 100 2; Error recovery delay (s): 300 3; Battery switch off delay (s): 300 4; Post heating circulation duration (s): 30 5; Pre heating circulation duration (s): 5 6; EEV error ignore time (s): 40 7; Well water flowrate heating(L/h): 500 8; Well water flowrate cooling(L/h): 300 9; Minimum well flowrate (L/h): 200 10; Minimum heating water flowrate (L/h): 300 11; Minimum well water discharge temperature (C): 4.0 12; Maximum condenser pressure (Bar): 24.0 13; Minimum superheat temperature (C): -4.0 14; Maximum superheat temperature (C): 30.0 15; Maximum compressor temperature (C): 100.0 16; Maximum starting pressure difference (Bar) 2.0 error: 13 s0 10 set option 0 to 10 (see above) Not in config mode! upsss, settings are password protected Prior to modify any settings please use "c <password>" to enter config mode. c 2135 the magic code Config mode ON s0 10 let's try again ls Operating settings: 0; Maximum compressor restart rate (1/hour): 10 1; Compressor Start delay (s): 100 2; Error recovery delay (s): 300 3; Battery switch off delay (s): 300 4; Post heating circulation duration (s): 30 5; Pre heating circulation duration (s): 5 6; EEV error ignore time (s): 40 7; Well water flowrate heating(L/h): 500 8; Well water flowrate cooling(L/h): 300 9; Minimum well flowrate (L/h): 200 10; Minimum heating water flowrate (L/h): 300 11; Minimum well water discharge temperature (C): 4.0 12; Maximum condenser pressure (Bar): 24.0 13; Minimum superheat temperature (C): -4.0 14; Maximum superheat temperature (C): 30.0 15; Maximum compressor temperature (C): 100.0 16; Maximum starting pressure difference (Bar) 2.0 error: 13 That's it.